Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM B111/B111M-18
Standard Specification for Copper and Copper-Alloy Seamless Condenser Tubes and Ferrule Stock
Přeložit název
NORMA vydána dne 1.3.2018
Informace o normě:
Označení normy: ASTM B111/B111M-18
Poznámka: NEPLATNÁ
Datum vydání normy: 1.3.2018
Kód zboží: NS-818525
Počet stran: 12
Přibližná hmotnost: 36 g (0.08 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM B111/B111M-18 :
Keywords:
condenser tube, copper, copper alloys, evaporator, ferrule stock, heat exchanger, seamless tube, UNS No. C10100, UNS No. C10200, UNS No. C10300, UNS No. C10800, UNS No. C12000, UNS No. C12200, UNS No. C14200, UNS No. C19200, UNS No. C23000, UNS No. C28000, UNS No. C44300, UNS No. C44400, UNS No. C44500, UNS No. C60800, UNS No. C61300, UNS No. C61400, UNS No. C68700, UNS No. C70400, UNS No. C70600, UNS No. C70620, UNS No. C71000, UNS No. C71500, UNS No. C71520, UNS No. C71640, UNS No. C72200,
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification2 establishes the requirements for seamless tube and ferrule stock of copper and various copper alloys up to 31/8 in. [80 mm] inclusive, in diameter, for use in surface condensers, evaporators, and heat exchangers. The following coppers and copper alloys are specified:3
1.2 Units—The values stated in either SI
units or inch-pound units are to be regarded separately as
standard. The values stated in each system may not be exact
equivalents; therefore, each system shall be used independently of
the other. Combining values from the two systems may result in
non-conformance with the standard.
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 19, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products in your state or country may be prohibited by law.) 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
