ASTM C1681-14
ASTM C564-14
ASTM C877M-02(2009)..
ASTM D1869-95(2010)..
ASTM D6396-99(2012)..
ASTM F1336-07
Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F2946-12
Standard Specification for PVC Hub and Elastomeric Seal (Gasket) Tee Connection for Joining Plastic Pipe to Insitu Pipelines and Manholes
Automaticky přeložený název:
Standardní specifikace pro PVC Hub a elastomerové těsnění (těsnění), T spoj pro spojení Plastová trubka na INSITU potrubí a šachet
NORMA vydána dne 1.8.2012
Informace o normě:
Označení normy: ASTM F2946-12
Poznámka: NEPLATNÁ
Datum vydání normy: 1.8.2012
Kód zboží: NS-54770
Počet stran: 4
Přibližná hmotnost: 12 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM F2946-12 :
Keywords:
elastomeric seal, rubber gasket, service connection, sewer tap, watertight seal, ICS Number Code 23.040.80 (Seals for pipe and hose assemblies)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||
|
1.1 This specification covers the minimum performance and material requirements for a three piece tee connector for connection between plastic pipe and insitu pipes, manholes and wastewater structures in sanitary and storm sewer applications. 1.1.1 The three piece seal system consists of a 4 through 30-in. PVC (polyvinyl chloride) hub pipe, an elastomeric seal (gasket) and a mechanical band (Fig. 1). The system is installed in either a bored or cast hole opening in the host pipe or structure to a specific dimension that corresponds to the combined diameter of the PVC pipe outside diameter/tolerance and the elastomeric seal thickness. FIG. 1 Three-Piece Sealing System
(Connector)
1.2 These tee connectors are designed to provide a non-pressure (gravity flow) watertight connection between the incoming pipe and an insitu pipe or manhole/structure to the limits defined in this standard. 1.3 The following precautionary
caveat pertains only to the test methods portion, Section
|
|
Standard Terminology Relating to Plastic Piping Systems
|
|
Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings
|
|
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings
|
|
Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
|
|
Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 (Includes all amendments and changes 10/8/2021).
|
|
Standard Terminology Relating to Rubber (Includes all amendments and changes 11/10/2021).
|
|
Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
|
|
Standard Terminology Relating to Concrete Pipe and Related Products
|
|
Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
|
|
Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Corrugated High Density Polyethylene and Polypropylene Pipelines
|
C900
|
Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 in. Through 12 in. (100 mm Through 300 mm), for Water Transmission and Distribution
|
|
Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings
|
|
Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air (Includes all amendments and changes 5/13/2020).
|
|
Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals |
Podobné normy:
Historická
1.6.2014
Historická
1.5.2014
Historická
1.10.2009
Historická
1.6.2010
Historická
1.10.2012
Historická
1.5.2007
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
