ASTM D3681-12e1
ASTM D3754-14
ASTM D3839-14
ASTM D3915-06
ASTM D3965-11
ASTM D4396-06
Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F2785-12
Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
Automaticky přeložený název:
Standardní specifikace pro polyamid 12 Gas tlakového potrubí, hadice a jejich příslušenství
NORMA vydána dne 1.8.2012
Informace o normě:
Označení normy: ASTM F2785-12
Poznámka: NEPLATNÁ
Datum vydání normy: 1.8.2012
Kód zboží: NS-54532
Počet stran: 13
Přibližná hmotnost: 39 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM F2785-12 :
Keywords:
ICS Number Code 23.040.20 (Plastic pipes), 23.040.45 (Plastic fittings)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers requirements and test methods for the characterization of polyamide 12 pipe, tubing, and fittings for use in fuel gas mains and services for direct burial and reliner applications. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas. 1.1.1 This specification does not cover threaded pipe. Generic fusion guidelines are given in 1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
OPS Part 192 Title 49
|
,Title 49 Code of Federal Regulations
|
|
Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
|
|
Standard Practice for Conditioning Plastics for Testing
|
|
Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
|
|
Standard Test Method for Tensile Properties of Plastics
|
|
Standard Test Method for Determination of Relative Viscosity of Concentrated Polyamide (PA) Solutions
|
|
Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
|
|
Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
|
|
Standard Practice for Sampling of Plastics (Withdrawn 1998)
|
|
Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
|
|
Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
|
|
Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
|
B 31.8
|
Gas Transmission and Distribution Piping Systems
|
|
Standard Specification for Excess Flow Valves for Natural Gas Service
|
|
Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
|
|
Standard Practice for Underground Installation of Thermoplastic Pressure Piping (Includes all amendments and changes 10/6/2021).
|
|
Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe (Includes all amendments and changes 9/12/2019).
|
|
Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
|
|
Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA)
|
|
Standard Terminology Relating to Plastic Piping Systems
|
|
Standard Guide for Selection and Use of Full-Encirclement-Type Band Clamps for Reinforcement or Repair of Punctures or Holes in Polyethylene Gas Pressure Pipe
|
|
Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins
|
|
Standard Specification for Butt Heat Fusion Polyamide(PA) Plastic Fitting for Polyamide(PA) Plastic Pipe and Tubing
|
|
Standard Specification for Factory Assembled Anodeless Risers and Transition Fittings in Polyethylene (PE) and Polyamide 11 (PA11) and Polyamide 12 (PA12) Fuel Gas Distribution Systems
|
|
Standard Specification for Electrofusion Type Polyamide-12 Fittings for Outside Diameter Controlled Polyamide-12 Pipe and Tubing for Gas Distribution
|
|
Standard Specification for Tracking and Traceability Encoding System of Natural Gas Distribution Components (Pipe, Tubing, Fittings, Valves, and Appurtenances) (Includes all amendments and changes 11/3/2023). |
Podobné normy:
Historická
1.4.2012
Historická
1.3.2014
Historická
1.3.2014
Historická
1.12.2006
Historická
1.9.2011
Historická
1.12.2006
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
