Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F2648/F2648M-23
Standard Specification for 50 mm to 1500 mm [2 in. to 60 in.] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications
Přeložit název
NORMA vydána dne 1.5.2023
Informace o normě:
Označení normy: ASTM F2648/F2648M-23
Datum vydání normy: 1.5.2023
Kód zboží: NS-1143496
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM F2648/F2648M-23 :
This specification covers the general requirements and corresponding test methods for non-pressure (gravity flow) polyethylene (PE) pipes and fittings having interior liner with annular corrugated exterior wall profile, and whose inside diameters are 2 to 60 in. [50 to 1500 mm]. These pipes and fittings are suitable for underground use in subsurface and land drainage systems, which do not operate under surcharge pressure heads. Material requirements are specified for pipe and blow molded fittings, rotationally molded fittings and couplings, injection molded fittings and couplings, and rework materials. The resulting products shall be tested as appropriate, and shall conform to specified requirements for workmanship, dimension (inside diameter, length, minimum inner liner thickness, and perforations), stiffness, flattening resistance, impact resistance, and slow crack growth resistance of PE plastics without pigment.
Keywords:
Profile wall, interior liner, pipe, fittings, PE, subdrainage, land drainage, polyethylene,, ICS Number Code 65.060.35 (Irrigation and drainage equipment)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||
|
1.1?This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with an interior liner. The inside diameters covered are 50 mm to 1500 mm [2 in. to 60 in.]. 1.2?The requirements of this specification are intended to provide non-pressure (gravity flow) pipe and fittings for underground use for subsurface and land drainage systems, which do not operate under surcharge pressure heads. Note 1:?Pipe and fittings produced in accordance with this
specification are be installed in compliance with Practice
D2321 or Practice
F449 based on diameter
limitations within the respective standards.
Note 2:?Subsurface and land drainage systems pertain
principally to non-municipal or private facilities for water table
control, storm drainage and agricultural drainage applications. The
products supplied under this specification are not intended for any
sanitary sewer or municipal storm sewer applications.
1.3?This specification covers pipe and fittings with an interior liner using an annular exterior corrugated profile (Fig. 1). 1.4?This specification permits the use of recycled materials for pipe in accordance with the requirements in Section 5. 1.5?UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
