Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

NEPLATNÁ ASTM F2648/F2648M-22 1.3.2022 náhled

Doplňující informace

ASTM F2648/F2648M-22

Standard Specification for 50 mm to 1500 mm [2 in. to 60 in.] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications

Přeložit název

NORMA vydána dne 1.3.2022

Jazyk
Provedení	PDF - okamžité stažení - 2 020.50 Kč Tištěné - 2 020.50 Kč
Dostupnost	SKLADEM
Cena	2020.50 Kč bez DPH
2 020.50 Kč

Informace o normě:

Označení normy: ASTM F2648/F2648M-22
Poznámka: NEPLATNÁ
Datum vydání normy: 1.3.2022
Kód zboží: NS-1052386
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Zavlažovací a drenážní zařízení

Anotace textu normy ASTM F2648/F2648M-22 :

Keywords:

Profile wall, interior liner, pipe, fittings, PE, subdrainage, land drainage, polyethylene,, ICS Number Code 65.060.35 (Irrigation and drainage equipment)

Doplňující informace

1. Scope

1.1?This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with an interior liner. The inside diameters covered are 50 mm to 1500 mm [2 in. to 60 in.].

1.2?The requirements of this specification are intended to provide non-pressure (gravity flow) pipe and fittings for underground use for subsurface and land drainage systems, which do not operate under surcharge pressure heads.

Note 1:?Pipe and fittings produced in accordance with this specification are be installed in compliance with Practice D2321 or Practice F449 based on diameter limitations within the respective standards.

Note 2:?Subsurface and land drainage systems pertain principally to non-municipal or private facilities for water table control, storm drainage and agricultural drainage applications. The products supplied under this specification are not intended for any sanitary sewer or municipal storm sewer applications.

1.3?This specification covers pipe and fittings with an interior liner using an annular exterior corrugated profile (Fig. 1).

1.4?This specification permits the use of recycled materials for pipe in accordance with the requirements in Section 5.

1.5?UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.

1.6?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

D618-21	Standard Practice for Conditioning Plastics for Testing
Fed. Stds. No. 123	Marking for Shipment (Civil Agencies)
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321-20	Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
D4218-20	Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
D5630-22	Standard Test Method for Ash Content in Plastics
D7209-06	Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015)
D7399-18	Standard Test Method for Determination of the Amount of Polypropylene in Polypropylene/Low Density Polyethylene Mixtures Using Infrared Spectrophotometry
F412-23	Standard Terminology Relating to Plastic Piping Systems
F449-20	Standard Practice for Subsurface Installation of Corrugated Polyethylene Pipe for Agricultural Drainage or Water Table Control
F2136-18(2024)	Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe
(AASHTO) AASHTO LRFD	Bridge Design Specifications
MIL-STD-129	Marking for Shipment and Storage
NCHRP Report 631	Updated Test and Design Methods for Thermoplastic Drainage Pipe
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)

Doporučujeme:

Aktualizace zákonů

Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.