Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F2648/F2648M-13
Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications
Automaticky přeložený název:
Standardní specifikace pro 2-60 palce [50 - 1500 mm] Annular Vlnitý profil Wall polyetylénu (PE) trubky a tvarovky pro Land Odvodňovací aplikace
NORMA vydána dne 1.1.2013
Informace o normě:
Označení normy: ASTM F2648/F2648M-13
Poznámka: NEPLATNÁ
Datum vydání normy: 1.1.2013
Kód zboží: NS-54309
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM F2648/F2648M-13 :
Keywords:
Profile wall, interior liner, pipe, fittings, PE, subdrainage, land drainage, polyethylene, ICS Number Code 65.060.35 (Irrigation and drainage equipment)
Doplňující informace
| 1. Scope | |||||
|
1.1 This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with an interior liner. The inside diameters covered are 2 to 60 in. [50 to 1500 mm]. 1.2 The requirements of this specification are intended to provide non-pressure (gravity flow) pipe and fittings suitable for underground use for subsurface and land drainage systems, which do not operate under surcharge pressure heads. 1.3 This specification covers pipe
and fittings with an interior liner using an annular exterior
corrugated profile (
Pipe Inside DiameterA |
Minimum Pipe Stiffness at 5% Deflection |
Minimum Inner Liner Thickness |
|||
|
inch |
[mm] |
lb/in/in |
[kPa] |
Inch |
[mm] |
|
2 |
[50] |
50 |
[345] |
0.020 |
[0.5] |
|
3 |
[75] |
50 |
[345] |
0.020 |
[0.5] |
|
4 |
[100] |
50 |
[345] |
0.020 |
[0.5] |
|
6 |
[150] |
50 |
[345] |
0.020 |
[0.5] |
|
8 |
[200] |
50 |
[345] |
0.024 |
[0.6] |
|
10 |
[250] |
50 |
[345] |
0.024 |
[0.6] |
|
12 |
[300] |
50 |
[345] |
0.035 |
[0.9] |
|
15 |
[375] |
42 |
[290] |
0.040 |
[1.0] |
|
18 |
[450] |
40 |
[275] |
0.051 |
[1.3] |
|
21 |
[525] |
38 |
[260] |
0.060 |
[1.5] |
|
24 |
[600] |
34 |
[235] |
0.060 |
[1.5] |
|
27 |
[675] |
30 |
[205] |
0.060 |
[1.5] |
|
30 |
[750] |
28 |
[195] |
0.060 |
[1.5] |
|
36 |
[900] |
22 |
[150] |
0.067 |
[1.7] |
|
42 |
[1050] |
20 |
[140] |
0.071 |
[1.8] |
|
48 |
[1200] |
18 |
[125] |
0.071 |
[1.8] |
|
54 |
[1350] |
16 |
[110] |
0.079 |
[2.0] |
|
60 |
[1500] |
14 |
[97] |
0.079 |
[2.0] |
1.4 This specification permits the
use of recycled materials for pipe in accordance with the
requirements in Section 5.
1.5 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
Standard Practice for Conditioning Plastics for Testing |
|
|
Fed. Stds. No. 123 |
Marking for Shipment (Civil Agencies) |
|
Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
|
|
Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications |
|
|
Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading |
|
|
Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight) |
|
|
Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
|
|
Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique |
|
|
Standard Test Method for Ash Content in Plastics |
|
|
Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015) |
|
|
Standard Test Method for Determination of the Amount of Polypropylene in Polypropylene/Low Density Polyethylene Mixtures Using Infrared Spectrophotometry |
|
|
Standard Terminology Relating to Plastic Piping Systems |
|
|
Standard Practice for Subsurface Installation of Corrugated Polyethylene Pipe for Agricultural Drainage or Water Table Control |
|
|
Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe |
|
|
(AASHTO) AASHTO LRFD |
Bridge Design Specifications |
|
MIL-STD-129 |
Marking for Shipment and Storage |
|
NCHRP Report 631 |
Updated Test and Design Methods for Thermoplastic Drainage Pipe |
|
Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024) |
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
