Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hydronic Heating Systems (Withdrawn 2020)
Automaticky přeložený název:
Standardní specifikace pro Vícevrstvé potrubí typu 2, kompresních tvarovek, a lisovací spojky pro otopné systémy
NORMA vydána dne 1.8.2011
Označení normy: ASTM F1987-01(2011)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.8.2011
Kód zboží: NS-52353
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
butt-welded aluminum pipe, compression fittings, crosslinkable, hydronic heating system, multilayer pipe, pipe, pressure, snap-ring, solder adapter, threaded adapter: Butt-welded materials/applications, Composites--piping applications (specifications), Compression-molded plastic specimens, Hydronic heating systems, Joints (pipe/tube applications)--specifications, Multilayer composite pipe, ICS Number Code 23.040.45 (Plastic fittings), 23.040.60 (Flanges, couplings and joints)
1. Scope | ||||||||||||||||||||||||||||||||||||
1.1 This specification covers requirements for multilayer pipe type 2 and compression fittings for hydronic heating systems, with a maximum pressure/temperature range of 1000 kPa (145 psi), at 82°C (180°F). Note 1—Multilayer Pipe Type 2Construction-based pressure rated pipe comprising more than one layer in which at least 60 % of the wall thickness is polymeric material. 1.2 Multilayer pipe type 2 is produced using a butt-welded aluminum pipe as a core, with an extruded inside layer of crosslinked polyethylene (PEX). An adhesive layer is used to bond the inside layer to the wall of the aluminum pipe. An outer layer of polyethylene (PE) and an adhesive layer are extruded to the outer wall of the aluminum pipe. 1.3 Multilayer pipe type 2 is produced in Configurations 1 and 2, as shown in Fig. 1. 1.4 This specification includes compression fittings, which are referenced in Fig. 2. 1.5 Specifications for threaded or solder adapters for use with pipe and fittings meeting the requirements of this specification are given in Annex A1 and Annex A2. 1.6 The following safety hazards caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this specification. |
||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||
|
Historická
15.11.2011
Historická
1.8.2012
Historická
1.11.2008
Historická
1.3.2010
Historická
1.2.2011
Historická
1.3.2008
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
Poslední aktualizace: 06.09.2024 (Počet položek: 2 346 102)
© Copyright 2024 NORMSERVIS s.r.o.