Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

NEPLATNÁ ASTM D2517-06(2011) 15.11.2011 náhled

Doplňující informace

ASTM D2517-06(2011)

Standard Specification for Reinforced Epoxy Resin Gas Pressure Pipe and Fittings

Automaticky přeložený název:

Standardní specifikace pro vyztužené epoxidové pryskyřice plynu tlakového potrubí a armatury

NORMA vydána dne 15.11.2011

Jazyk
Provedení	PDF - okamžité stažení - 2 010.10 Kč Tištěné - 2 010.10 Kč
Dostupnost	SKLADEM
Cena	2010.10 Kč bez DPH
2 010.10 Kč

Informace o normě:

Označení normy: ASTM D2517-06(2011)
Poznámka: NEPLATNÁ
Datum vydání normy: 15.11.2011
Kód zboží: NS-20634
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Trubky z plastické hmoty
Fitinky z plastické hmoty

Anotace textu normy ASTM D2517-06(2011) :

Keywords:

filament wound, compression molded, configuration of joining system, rupture srength, crush strength, chemical resistance, apparent tensile properties, adhesive, Shear testing--adhesives, Compression-molded plastic specimens, Configuration of joining system, Filament-wound plastic pipe, Gas pressure systems/applications--specifications, Reinforced thermosetting-resin pipe (RTRP)--specifications, ICS Number Code 23.040.20 (Plastic pipes), 23.040.45 (Plastic fittings)

Doplňující informace

1. Scope

1.1 This specification covers requirements and methods of test for materials, dimensions and tolerances, hydrostatic-burst strength, chemical resistance, and longitudinal tensile properties, for reinforced epoxy resin pipe and fittings for use in gas mains and services for direct burial and insertion applications. The pipe and fittings covered by this specification are intended for use in the distribution of natural gas, petroleum fuels (propane–air and propane–butane vapor mixtures), manufactured and mixed gases where resistance to gas permeation, toughness, resistance to corrosion, aging, and deterioration from water, gas, and gas additives are required. Methods of marking are also given. Design considerations are discussed in Appendix X1.

1.2 The values in SI units are to be regarded as the standard.

1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1—There is no known ISO equivalent to this standard.

1.4 A recommended inplant quality control program is given in Appendix X2.

2. Referenced Documents

D5685-19	Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings
D883-24	Standard Terminology Relating to Plastics
D2143-21	Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe
D2105-01(2019)	Standard Test Method for Longitudinal Tensile Properties of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Tube
D1898-68(1989)	Standard Practice for Sampling of Plastics (Withdrawn 1998)
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D2992-22	Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
D2996-23	Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
D3567-17(2022)	Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
D3839-14(2019)	Standard Guide for Underground Installation of “Fiberglass” (Glass-Fiber Reinforced Thermosetting-Resin) Pipe
D3892-15(2020)	Standard Practice for Packaging/Packing of Plastics
F412-23	Standard Terminology Relating to Plastic Piping Systems
D2290-19a	Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe (Includes all amendments and changes 9/12/2019).
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D396-21	Standard Specification for Fuel Oils
D543-21	Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D618-21	Standard Practice for Conditioning Plastics for Testing
D2924-24	Standard Test Method for External Pressure Resistance of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe