Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Multilayer Pipe Type 2, Compression Fittings, and Compression Joints for Hot and Cold Drinking-Water Systems (Withdrawn 2020)
Automaticky přeložený název:
Standardní specifikace pro Vícevrstvé potrubí typu 2, kompresních tvarovek, a lisovací spojky na teplé a studené pitné vody Systems
NORMA vydána dne 1.8.2011
Označení normy: ASTM F1986-01(2011)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.8.2011
Kód zboží: NS-52349
Počet stran: 12
Přibližná hmotnost: 36 g (0.08 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
butt-welded aluminum pipe, compression fittings, hot and cold drinking-water, multilayer pipe, pipe, pressure, snap-ring, solder adapter, threaded adapter: Cold water supply/distribution systems--specifications, Composites--piping applications (specifications), Compression-molded plastic specimens, Hot water supply/distribution systems--specifications, Joints (pipe/tube applications)--specifications, Multilayer composite pipe, Pressure vessel plastic, Solder adapter, Threaded adapter
1. Scope | ||||||||||||||||||||||||||||||||||||||||
1.1 This specification covers requirements for multilayer pipe type 2 and compression fittings for hot and cold drinking-water systems, with a maximum pressure rating of 1000 kPa (145 psi) at 82°C (180°F). Note 1—Multilayer Pipe Type 2Construction-based pressure rated pipe comprising more than one layer in which at least 60 % of the wall thickness is polymeric material. 1.2 Multilayer pipe type 2 is produced using a butt-welded aluminum pipe as a core, with an extruded inside layer of crosslinked polyethylene (PEX). An adhesive layer is used to bond the inside layer to the wall of the aluminum pipe. An outer layer of polyethylene (PE) and an adhesive layer are extruded to the outer wall of the aluminum pipe. 1.3 Multilayer pipe type 2 is produced in configurations 1 and 2, as referenced in Fig. 1. 1.4 This specification includes compression fittings, which are referenced in Fig. 2 . 1.5 Specifications for thread or solder adapters for use with pipe and fittings meeting the requirements of this specification are given in Annex A1 and Annex A2. 1.6 The following precautionary caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. |
||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||
|
Historická
1.12.2006
Historická
1.9.2011
Historická
1.11.2010
Historická
1.2.2011
Historická
1.12.2011
Historická
1.5.2010
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 06.09.2024 (Počet položek: 2 346 102)
© Copyright 2024 NORMSERVIS s.r.o.