Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM D5685-11

Standard Specification for ""Fiberglass"" (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe Fittings

Automaticky přeložený název:

Standardní specifikace pro "skleněných vláken" (skelnými vlákny vyztužený Teplem-pryskyřice) Kování tlakového potrubí

NORMA vydána dne 1.2.2011

Jazyk
Provedení	PDF - okamžité stažení - 1 746.20 Kč Tištěné - 1 746.20 Kč
Dostupnost	SKLADEM
Cena	1 746.20 Kč bez DPH
1 746.20 Kč

Informace o normě:

Označení normy: ASTM D5685-11
Poznámka: NEPLATNÁ
Datum vydání normy: 1.2.2011
Kód zboží: NS-32178
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Fitinky z plastické hmoty

Anotace textu normy ASTM D5685-11 :

Keywords:
centrifugally cast, compression molded, contact molded, degree of cure, epoxy-resin, filament-wound, furan-resin, glass transition temperature, percent extractable material, polyester-resin, pressure-rating, transfer molded, Centrifugally cast plastic pipe--specifications, Compression-molded plastic specimens, Contact molded pipe/flanges--specifications, Epoxy resin pipe fittings--specifications, Fiberglass pipe--specifications, Filament-wound plastic pipe, Glass-fiber-reinforced (GRP) plastics

Doplňující informace

1. Scope

1.1 This specification covers “fiberglass” (glass-fiber-reinforced thermosetting-resin) fittings for use with filament wound or centrifugally cast fiberglass pipe, or both, in sizes 1 in. through 24 in. for pipe manufactured to Specification D2996 or D2997, or both.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following safety hazard caveat pertains only to the test method portion, Section 7, of this specification:

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1—The term “fiberglass pipe” as described in Section 3 of this specification applies to both reinforced thermosetting resin pipe (RTRP) and reinforced polymer mortar pipe (RPMP).

Note 2—For the purposes of this standard, ploymer does not include natural polymers.

Note 3—There is no known ISO equivalent to this standard.

A1.1.1 This test determines whether the degree of cure of a fiberglass fitting test specimen meets the quality control requirements determined by statistical analysis of typical production products.

2. Referenced Documents

F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
B16.5	Steel Pipe Flanges, Flanged Valves and Fittings Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
D2997-21	Standard Specification for Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
D2996-23	Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
D2992-22	Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
D2310-06	Standard Classification for Machine-Made ""Fiberglass"" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe
D3567-17(2022)	Standard Practice for Determining Dimensions of “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D883-24	Standard Terminology Relating to Plastics
D618-21	Standard Practice for Conditioning Plastics for Testing
D2143-21	Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe
F412-23	Standard Terminology Relating to Plastic Piping Systems
D4024-22	Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges