Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM E1797-12(2017)e1
Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings (Includes all amendments and changes 5/16/2019).
Přeložit název
NORMA vydána dne 1.10.2017
Informace o normě:
Označení normy: ASTM E1797-12(2017)e1
Datum vydání normy: 1.10.2017
Kód zboží: NS-799300
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM E1797-12(2017)e1 :
This specification covers minimum material performance requirements and laboratory test procedures for reinforced liquid coating encapsulation products (single- or multiple-coat systems) for leaded paint in buildings. It applies to any liquid-applied product incorporating reinforcement materials as part of the system. Reinforcement materials are continuous fabric or mesh and are applied in the field. These materials are typically applied between a base and top coat. These products are used to encapsulate a leaded paint surface with the intent of reducing human exposure to lead in paint. These are classified into three types which are Type I which are encapsulation products are intended for interior use, Type II which are encapsulation products intended for exterior use, and Type III which defines encapsulation products intended for either interior or exterior use. Different tests shall be conducted in order to determine the following performance properties for reinforced liquid coating encapsulation products such as impact resistance, adhesion, dry abrasion resistance, water vapor transmission, water resistance, chemical resistance, surface burning characteristics, volatile organic compound content, weathering, aging, scrub resistance, mildew resistance, paint ability and repairability. Testing conducted shall be performed on the entire encapsulation product system, whether single or multiple coat, as applied in the field, except for scrub resistance, volatile organic compound (VOC) content, and permeability, which are performed on the top coat only.
Keywords:
abatement, encapsulant, encapsulation, lead, leaded paint, liquid coating, liquid coating encapsulation product, reinforced liquid coating encapsulation product ,, ICS Number Code 87.040 (Paints and varnishes)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers minimum material performance requirements and laboratory test procedures for reinforced liquid coating encapsulation products (single- or multiple-coat systems) for leaded paint in buildings. Performance properties addressed in this specification are: 1.1.1 Impact Resistance, 1.1.2 Adhesion, 1.1.3 Dry Abrasion Resistance, 1.1.4 Water Vapor Transmission, 1.1.5 Water and Chemical Resistance, 1.1.6 Surface Burning Characteristics, 1.1.7 Volatile Organic Compound (VOC) Content, 1.1.8 Weathering, 1.1.9 Aging, 1.1.10 Scrub Resistance, 1.1.11 Mildew Resistance, 1.1.12 Paintability/Repairability, 1.2 This specification does not address the selection of an encapsulation product for specific use conditions. Specific use conditions may require performance values other than those stated in this specification. See Guide E1796 for guidance. 1.3 This specification complements Specification E1795 for non-reinforced liquid coating encapsulation products. 1.4 This specification does not cover the use of encapsulation products on industrial steel structures nor residential exterior coated metal surfaces because no corrosion control requirements are included. 1.5 This specification applies to any liquid-applied product incorporating reinforcement materials as part of the system. Reinforcement materials are continuous fabric or mesh and are applied in the field. These materials are typically applied between a base and top coat. These products are used to encapsulate a leaded paint surface with the intent of reducing human exposure to lead in paint. 1.6 The results of the test methods included in this specification will not necessarily predict field performance. 1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
