Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D3273-21
Standard Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber
Přeložit název
NORMA vydána dne 1.11.2021
Informace o normě:
Označení normy: ASTM D3273-21
Datum vydání normy: 1.11.2021
Kód zboží: NS-1045087
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D3273-21 :
Keywords:
environmental chamber, mold, surface interior coatings,, ICS Number Code 87.040 (Paints and varnishes)
Doplňující informace
| Significance and Use | ||||
|
3.1?An accelerated test for determining the resistance of interior coatings to mold growth is useful in estimating the performance of coatings designed for use in interior environments that promote mold growth and in evaluating compounds that may inhibit such growth and the aggregate levels for their use (see also Note 1). 3.2?This test method should preferably be used by persons who have had basic microbiological training. |
||||
| 1. Scope | ||||
|
1.1?This test method describes the use of an environmental chamber and operating conditions to evaluate the relative resistance of interior coatings to surface fungal growth in a severe interior environment during a 4-week period. 1.2?This test method can be used to evaluate the comparative resistance of interior coatings to accelerated mold growth. Performance at a certain rating does not imply any specific period of time for a fungal free coating. However, a better rated coating nearly always performs better in actual end use. Note 1:?This test method is intended for the accelerated
evaluation of an interior coatings resistance to fungal defacement.
Use of this test method for evaluating exterior coatings
performance has not been validated, nor have the limitations for
such use been determined. If this test method is to be used for the
testing of an exterior coating system, a precautionary statement
regarding interpretation of results as being outside of the scope
of this test method must be included in the test report. Any
accelerated weathering (leaching, weathering machine exposure,
etc.) should be reported and should also bear reference to the fact
that it is beyond the current scope of this test method.
1.3?Temperature and humidity must be effectively controlled within the relatively narrow limits specified in order for the chamber to function reproducibly during the short test period. Severity and rate of mold growth on a film is a function of the moisture content of both the film and the substrate. A relative humidity of >93 % at a temperature of 32.5 ? 1 ?C (90 ? 2 ?F ) is necessary to initiate and maintain mold growth and for test panels to develop rapidly and maintain an adequate moisture level to support mold growth. 1.4?The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||
| 2. Referenced Documents | ||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
