Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D7870/D7870M-13
Standard Practice for Moisture Conditioning Compacted Asphalt Mixture Specimens by Using Hydrostatic Pore Pressure
Automaticky přeložený název:
Standardní praktiky pro Moisture Klimatizace Kompaktní asfaltové směsi vzorků pomocí hydrostatický tlak pórů
NORMA vydána dne 1.6.2013
Informace o normě:
Označení normy: ASTM D7870/D7870M-13
Poznámka: NEPLATNÁ
Datum vydání normy: 1.6.2013
Kód zboží: NS-39211
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D7870/D7870M-13 :
Keywords:
antistripping additives, asphalt concrete paving mixtures, cyclic stress, moisture, moisture conditioning, pore pressure, tensile strength, water, ICS Number Code 75.140 (Waxes, bituminous materials and other petroleum products)
Doplňující informace
| Significance and Use | ||||||||||||||||||||||||||||
|
3.1 This practice provides an accelerated conditioning method under cyclic loading. This system is capable of operating at higher than normal temperatures and creating pore pressure within a compacted asphalt mixture to achieve an acceleration of the effects that a mixture would experience over time from traffic at normal temperatures and conditions. The accelerated conditioning in this practice is intended to simulate the stresses induced in a wet pavement by a passing vehicle tire. The pulse shape produced by this system approximates a Lorentzian function with a half peak width of approximately 1 s at 276 kPa [40 psi]. 3.2 The factors that influence the potential for moisture damage to occur include aggregate mineralogy, mixture air voids, water, cyclic applied stress, and elevated temperature. This practice provides a method and apparatus that is capable of producing three of these factors: water, stress, and high temperature. Aggregate mineralogy and air voids are mixture properties. 3.3 Specimens conditioned by this system can be tested using a variety of different tests including, Test Method D6931, Test Method D6927, bulk specific gravity difference obtained by Test Methods D6926 or D6752 for before and after conditioning, dynamic modulus, flow number, AASHTO TP 79 and visual inspection for stripped aggregates. 1.1 This practice includes
procedures for preparing compacted asphalt mixture specimens,
exposing the specimens to hydrostatic pore pressure inside an
enclosed chamber and guidance on testing the specimens for the
effect of water on the tensile strength or change in other
properties of the asphalt mixture, such as density, modulus,
etc.
1.2 Specimens conditioned according to this practice can be tested using methods and test procedures referenced in this document and those results may provide information as to the effect of the moisture conditioning of this practice on the moisture sensitivity of those mixtures. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||
|
Doporučujeme:
