Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D7793-21
Standard Specification for Insulated Vinyl Siding
Přeložit název
NORMA vydána dne 1.12.2021
Informace o normě:
Označení normy: ASTM D7793-21
Datum vydání normy: 1.12.2021
Kód zboží: NS-1043997
Počet stran: 14
Přibližná hmotnost: 42 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D7793-21 :
Keywords:
insulated siding, insulated vinyl siding, plastic building products, plastic weatherability, recycled plastic, rigid PVC siding, specification, vinyl siding,, ICS Number Code 29.035.20 (Plastic and rubber insulating materials),83.080.20 (Thermoplastic materials)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1This specification establishes requirements for insulated vinyl siding, which is vinyl siding with integral foam plastic insulating material, where the vinyl siding is manufactured from rigid PVC compound. Compliance with this standard requires insulated vinyl siding to demonstrate a thermal insulation value of R-2.0 or greater. Other performance requirements and test methods addressed by this standard include materials properties and dimensions, warp, shrinkage, impact strength, expansion, appearance, thermal distortion resistance, flame spread, and windload resistance. Methods of indicating compliance with this specification are also provided. Note 1:Insulated vinyl siding is composed of two major
components: the vinyl siding and the insulating material. It is
intended that the vinyl siding portion comply with Specification
D3679. Applicable portions of
Specification D3679 are
included in this specification. Additional requirements that
pertain only to the insulation as a separate material, or to the
combination of vinyl siding and insulation as a whole, are also
included. For further explanation, see Appendix X1.
1.2Insulated vinyl siding shall be tested with the insulation material in place or removed, as specified in the applicable requirement or test method. 1.3The use of PVC recycled plastic in this product shall be in accordance with the requirements in Section 4. 1.4Insulated vinyl siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to the manufacturer's installation instructions for the specific product to be installed. 1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 2:There is no known ISO equivalent to this
standard.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
