Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D7484-08
Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine
Automaticky přeložený název:
Standardní zkušební metoda pro hodnocení Oleje Automotive motorem pro Valve -Train výkon nosí v Cummins ISB středně náročné vznětový motor
NORMA vydána dne 15.10.2008
Informace o normě:
Označení normy: ASTM D7484-08
Poznámka: NEPLATNÁ
Datum vydání normy: 15.10.2008
Kód zboží: NS-38576
Počet stran: 25
Přibližná hmotnost: 75 g (0.17 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM D7484-08 :
Keywords:
diesel engine oil, heavy-duty engine oil, ISB medium-duty diesel engine, lubricants, valve-train wear, ICS Number Code 75.100 (Lubricants, industrial oils and related products)
Doplňující informace
| Significance and Use | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
This test method was developed to assess the performance of a heavy-duty engine oil in controlling engine wear under operating conditions selected to accelerate soot production and valve-train wear in a turbocharged and aftercooled four-cycle diesel engine with sliding tappet followers equipped with exhaust gas recirculation hardware. The design of the engine used in this test method is representative of many, but not all, modern diesel engines. This factor, along with the accelerated operating conditions, shall be considered when extrapolating test results. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This test method, commonly referred to as the Cummins ISB Test, covers the utilization of a modern, 5.9-L, diesel engine equipped with exhaust gas recirculation and is used to evaluate oil performance with regard to valve-train wear. 1.2 The values stated in either SI units, inch-pound units, or other units are to be regarded separately as the primary units. 1.2.1 For each parameter, the primary units are shown first. Secondary units may be shown in parentheses, for information purposes only. These secondary units may or may not be exact equivalents to the primary units. 1.2.2 SI units are provided for all parameters except where there is no direct equivalent such as the units for screw threads, national pipe threads/diameters, and tubing size. 1.2.3 See also A8.1 for clarification; it does not supersede 1.2.1 and 1.2.2. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A1 for general safety precautions. 1.4 Table of Contents:
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
