Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D6823-08(2021)
Standard Specification for Commercial Boiler Fuels With Used Lubricating Oils
Přeložit název
NORMA vydána dne 1.11.2021
Informace o normě:
Označení normy: ASTM D6823-08(2021)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2021
Kód zboží: NS-1042207
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D6823-08(2021) :
Keywords:
burner fuels, fuel oils, petroleum and petroleum products, specifications, used oils,, ICS Number Code 75.100 (Lubricants, industrial oils and related products)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1?This specification covers four grades of fuel oil made of at least 25 % used lubricating oils. The four grades of fuel are intended for use in various types of fuel-oil-burning industrial equipment and commercial boilers under various climatic and operating conditions. These fuels are not intended for use in residential heaters. 1.1.1?Grades RFC4, RFC5L, RFC5H and RFC6 are used lubricating oil blends of increasing viscosity, with or without middle distillate or residual fuel oil, or both, that are intended for use in industrial burners and commercial boilers equipped to handle these types of fuels. This specification is for applications where Specification D6448 would not meet the performance or other requirements of the burner or boiler in question. Note 1:?For information on the significance of the terminology
and test methods used in this specification, see Appendix X1.
1.2?This specification is for use in contracts for the purchase of fuel oils derived from used lubricating oil and for the guidance of consumers of such fuels. This specification does not address the frequency with which any particular test must be run. 1.3?Nothing in this specification shall preclude observance of national or local regulations which can be more restrictive. In some jurisdictions, used oil is considered a hazardous waste and fuels derived from used oil are required to meet certain criteria before use as a fuel. Note 2:?For United States federal requirements imposed on used
oil generators, transporters and transfer facilities, reprocessors,
marketers, and burners, see 40 CFR Part 279.
Note 3:?The generation and dissipation of static electricity
can create problems in the handling of distillate burner fuel oils.
For more information on the subject, see Guide D4865.
1.4?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4.1?ExceptionTable 1 and Table X1.1 include inch-pound values in parentheses for information only. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
