Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester (Includes all amendments and changes 7/27/2021).
Přeložit název
NORMA vydána dne 1.7.2021
Označení normy: ASTM D6450-16a(2021)
Datum vydání normy: 1.7.2021
Kód zboží: NS-1030392
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
continuously closed cup, flammability, flash point,, ICS Number Code 75.080 (Petroleum products in general)
Significance and Use | ||||||||||||||
5.1?The flash point temperature is one measure of the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions. It is only one of a number of properties that must be considered in assessing the overall flammability hazard of a material. 5.2?Flash point is used in shipping and safety regulations to define flammable and combustible materials and classify them. This definition may vary from regulation to regulation. Consult the particular regulation involved for precise definitions of these classifications. 5.3?This test method can be used to measure and describe the properties of materials in response to heat and an ignition source under controlled laboratory conditions and shall not be used to describe or appraise the fire hazard or fire risk of materials under actual fire conditions. However, results of this test method may be used as elements of a fire risk assessment, which takes into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use. 5.4?Flash point can also indicate the possible presence of highly volatile and flammable materials in a relatively nonvolatile or nonflammable material, such as the contamination of lubricating oils by small amounts of diesel fuel or gasoline. |
||||||||||||||
1. Scope | ||||||||||||||
1.1?This flash point test method is a dynamic method and depends on definite rates of temperature increase. It is one of the many flash point test methods available, and every flash point test method, including this one, is an empirical method. Note 1:?Flash point values are not a constant
physical-chemical property of materials tested. They are a function
of the apparatus design, the condition of the apparatus used, and
the operational procedure carried out. Flash point can therefore
only be defined in terms of a standard test method, and no general
valid correlation can be guaranteed between results obtained by
different test methods or with test apparatus different from that
specified.
1.2?This test method covers the determination of the flash point of fuel oils, lube oils, solvents, and other liquids by a continuously closed cup tester. The measurement is made on a test specimen of 1 mL. 1.3?This test method utilizes a closed but unsealed cup with air injected into the test chamber. 1.4?This test method is suitable for testing samples with a flash point from 10 ?C to 250 ?C. Note 2:?Flash point determinations below 10 ?C and above 250
?C can be performed; however, the precision has not been determined
below and above these temperatures.
1.5?If the user's specification requires a defined flash point method other than this test method, neither this test method nor any other method should be substituted for the prescribed method without obtaining comparative data and an agreement from the specifier. 1.6?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Temperatures are in degrees Celsius, and pressure is in kilo-pascals. 1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||
2. Referenced Documents | ||||||||||||||
|
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
Poslední aktualizace: 22.11.2024 (Počet položek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.