ASTM E691-14
ASTM F2048-00(2009)..
ASTM F2717-14
ASTM G136-03(2009)..
ASTM G141-09(2013)..
ASTM G147-09
Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D5966-13
Standard Test Method for Evaluation of Engine Oils for Roller Follower Wear in Light-Duty Diesel Engine (Withdrawn 2022)
Automaticky přeložený název:
Standardní zkušební metoda pro vyhodnocení oleje motoru pro Roller Follower Používejte lehkých užitkových dieselový motor
NORMA vydána dne 1.5.2013
Informace o normě:
Označení normy: ASTM D5966-13
Poznámka: NEPLATNÁ
Datum vydání normy: 1.5.2013
Kód zboží: NS-33235
Počet stran: 19
Přibližná hmotnost: 57 g (0.13 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Zkušební podmínky a postupy všeobecně
Maziva, průmyslové oleje a odpovídající výrobky
Anotace textu normy ASTM D5966-13 :
Keywords:
calibrate, diesel engine, engine oil, light-duty, light-duty engine, lubricant, reference oil, roller follower shaft wear, used oil wear, ICS Number Code 19.020 (Test conditions and procedures in general),75.100 (Lubricants, industrial oils and related products)
Doplňující informace
| Significance and Use | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
5.1 This test method is used to determine the ability of an engine crankcase oil to control wear that can develop in the field under low to moderate engine speeds and heavy engine torques. Side-by-side comparisons of two or more oils in delivery van fleets were used to demonstrate the field performance of various oils. The specific operating conditions of this test method were developed to provide correlation with the field performance of these oils. 5.2 This test method, along with other test methods, defines the minimum performance level of the Category API CG-4 for heavy duty diesel engine lubricants. Passing limits for this category are included in Specification D4485. 5.3 The design of the engine used in this test method is not representative of all modern diesel engines. Consider this factor, along with the specific operating conditions used to accelerate wear, when extrapolating test results. |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 1. Scope | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This engine lubricant test method is commonly referred to as the Roller Follower Wear Test. Its primary result, roller follower shaft wear in the hydraulic valve lifter assembly, has been correlated with vehicles used in stop-and-go delivery service prior to 1993. It is one of the test methods required to evaluate lubricants intended to satisfy the API CG-4 performance category. This test has also been referred to as the 6.2 L Test. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.2.1 Exceptions—Where there is no direct SI equivalent, such as pipe fittings, thermocouple diameters, and NPT screw threads. Also, roller follower wear is measured in mils. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 Table of Contents:
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Podobné normy:
Historická
1.4.2014
Historická
1.1.2009
Historická
1.5.2014
Historická
1.4.2009
Historická
1.11.2013
Historická
1.2.2009
Doporučujeme:
