Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Mass Per Unit Area of Pile Yarn Floor Coverings (Withdrawn 2019) (Includes all amendments And changes 6/4/2020).
Automaticky přeložený název:
Standardní zkušební metoda pro plošnou hmotností vlasu příze podlahových krytin
NORMA vydána dne 1.6.2010
Označení normy: ASTM D5848-10e1
Poznámka: NEPLATNÁ
Datum vydání normy: 1.6.2010
Kód zboží: NS-32777
Počet stran: 13
Přibližná hmotnost: 39 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
carpet, construction, floor covering, mass per unit area, pile yarn, Carpets, Construction--textile fabrics/fibers, Flooring/floor covering systems (textiles), Mass per unit area, Pile yarn floor coverings, ICS Number Code 97.150 (Floor coverings)
Significance and Use | ||||||||||||||||||
The determination of the mass per unit area of pile yarn floor covering is useful in quality and cost control during the manufacture of pile floor covering. Both appearance and performance may be affected by changes in mass per unit area. In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and supplier should conduct comparison testing to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties prior to testing. If a bias is found, either its cause must be found and corrected or the purchaser and supplier must agree to interpret future test results with consideration to the known bias. |
||||||||||||||||||
1. Scope | ||||||||||||||||||
1.1 This test method covers the measurement of mass per unit area of machine-made woven, knitted, and tufted pile yarn floor covering both before and after an adhesive-back coating application. 1.2 This test method encompasses three techniques for determination of mass per unit area as applicable: 1.2.1 Section 1.3, for determining total mass per unit area, applies to both coated and uncoated (unfinished) pile floor coverings. 1.2.2 Section 1.4, for determining component mass per unit area, applies only to uncoated (unfinished) pile yarn floor coverings. 1.2.3 Section 1.5, for determining pile yarn mass per unit area, applies only to back-coated, or finished, pile yarn floor coverings. 1.3 Determination of mass per unit area of pile yarn floor coverings was previously contained within Test Methods . For user convenience, Subcommittee D 13.21 subdivided Test Methods into separate standards, of which this test method is one. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 9.5. |
||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||
|
Historická
1.10.2011
Historická
15.4.2013
Historická
1.7.2012
Historická
1.3.2009
Historická
15.9.2011
Historická
1.8.2011
Poslední aktualizace: 22.11.2024 (Počet položek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.