Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D5146-10(2019)
Standard Guide to Testing Solvent-Borne Architectural Coatings
Přeložit název
NORMA vydána dne 1.1.2019
Informace o normě:
Označení normy: ASTM D5146-10(2019)
Datum vydání normy: 1.1.2019
Kód zboží: NS-910838
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D5146-10(2019) :
This guide covers the selection and use of procedures for testing solvent-borne architectural coatings to be used on exterior, interior, or both types of surfaces. The properties that can be examined by the test methods listed herein are as follows: liquid paint properties (skinning, condition in container, coarse particles and foreign matter, density or weight per gallon, fineness of dispersion, flash point, odor, absorption, colorant acceptance, dilution stability, package stability, heat stability, and settling); coating application and film formation characteristics (brush application properties, brush drag, roller application properties, roller spatter, spray application properties, touch-up uniformity, consistency (low-shear viscosity), rheological properties of non-Newtonian liquids, sag resistance, levelling properties, and drying properties); appearance of dry film (color appearance, color differences by visual comparison, color differences using instrumental measurements, directional reflectance, gloss, sheen, hiding power, and yellowness index); properties of dry film (abrasion resistance, adhesion, flexibility, resistance to household chemicals, color change of white enamels, washability and cleansability, blister resistance, exposure resistance, chalking, checking, cracking, erosion, flaking, mildew resistance, and fume resistance); and Coating Analysis (chemical analysis, volatile content, nonvolatile volume content, water content, pigment content, pigment analysis, nonvolatile vehicle content, vehicle separation, and nonvolatile vehicle identification).
Keywords:
architectural coatings, coatings tests, solvent-borne coatings, water-borne coatings,, ICS Number Code 87.040 (Paints and varnishes)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This guide covers the selection and use of procedures for testing solvent-borne coatings to be used on exterior, interior or both types of surfaces (see Note 1). The properties that can be examined or, in some cases, the relevant test procedures are listed in Table 1 and Table 2. Note 1: The term “architectural coating” as used here combines
the definition in Terminology D16 with that in the FSCT Paint/Coatings
Dictionary, as follows: “Organic coatings intended for on-site
application to interior or exterior surfaces of residential,
commercial, institutional, or industrial buildings, in contrast to
industrial coatings. They are protective and decorative finishes
applied at ambient temperatures. Often called Trade Sales
Coatings.”
Note 2: Architectural coatings that are designed to give
better performance than most conventional coatings because they are
tougher and more stain- and abrasion-resistant are covered by Guide
D3730.
1.2 The types of organic coatings covered by this guide are as follows: (1) Type 1 Interior Low-Gloss Wall Finish, (2) Type 2 Interior Gloss and Semigloss Wall and Trim Enamels, (3) Type 3 Exterior House and Trim Coatings, and (4) Type 4 Floor Enamel, Exterior and/or Interior. 1.2.1 Each is intended for application by brushing, rolling, spraying, or other means to the materials appropriate for its type, which may include wood, plaster, wallboard, masonry, steel, previously painted surfaces, and other architectural substrates. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
