Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Guide for Use of Adhesive-Bonded Single Lap-Joint Specimen Test Results (Includes all amendments And changes 5/16/2016).
Automaticky přeložený název:
Standardní průvodce pro použití lepidla vázané Jednotlivé Lap-Joint zkušebního vzorku výsledky
NORMA vydána dne 1.4.2008
Označení normy: ASTM D4896-01(2008)e1
Poznámka: NEPLATNÁ
Datum vydání normy: 1.4.2008
Kód zboží: NS-29062
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
shear strength, single-lap joint, tension loading, Cleavage testing, Design stresses, Edge flaws, Environmental control/fate, Joints (adhesives), Permeability, Single lap-joint adhesive specimen, Thick/thin adherend, Volumetric measurement, Bond strength--adhesives, Degradation--adhesives, Moisture analysis--adhesives, Peel strength tests--adhesives, Shear testing--adhesives, Strain testing--adhesives, Strength--adhesives, Stress--adhesives, Temperature tests--adhesives, Adherence
Significance and Use | ||||||||||||||||||||||||||||||||||||||||||||||||||
Single-lap specimens are economical, practical, and easy to make. They are the most widely used specimens for development, evaluation, and comparative studies involving adhesives and bonded products, including manufacturing quality control. Special specimens and test methods have been developed that yield accurate estimates of the true shear strength of adhesives. These methods eliminate or minimize many of the deficiencies of the thin-adherend single-lap specimens, but are more difficult to make and test. (See Test Methods D 3983, D 4027, D 4562, and E 229.) The misuse of strength values obtained from such Test Methods or Practices as D 906, D 1002, D 1144, D 1151, D 1183, D 1780, D 2294, D 2295, D 2339, D 3163, D 3164, D 3165, D 3434, D 3528, D 3632, and D 5868, as allowable design-stress values for structural joints could lead to product failure, property damage, and human injury. |
||||||||||||||||||||||||||||||||||||||||||||||||||
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||
1.1 This guide is directed toward the safe and appropriate use of strength values obtained from test methods using single-lap adhesive joint specimens. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The discussion focuses on shear strength as measured with small thin-adherend, single-lap specimens. Many factors, however, apply to shear modulus, tensile strength, and tensile modulus measured by small laboratory specimens in general. This discussion is limited to single-lap specimens and shear strength only for simplification. |
||||||||||||||||||||||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||
|
Historická
1.3.2014
Historická
1.4.2008
Historická
1.2.2011
Historická
1.4.2008
Historická
1.4.2008
Historická
1.4.2008
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 04.11.2024 (Počet položek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.