Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D4067-23
Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods
Přeložit název
NORMA vydána dne 1.2.2023
Informace o normě:
Označení normy: ASTM D4067-23
Datum vydání normy: 1.2.2023
Kód zboží: NS-1135564
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D4067-23 :
This classification system covers reinforced and filled poly(phenylene sulfide) (PPS) materials suitable for injection molding and extrusion. This classification system is not intended for the selection of materials, but only as a means to call out plastic materials to be used for the manufacture of parts. The physical properties of the materials must meet the required tensile strength, flexural modulus, Izod impact strength, flexural strength, and density.
Keywords:
plastic materials, poly(phenylene sulfide),, ICS Number Code 83.120 (Reinforced plastics)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||
|
1.1?This classification system covers reinforced and filled poly(phenylene sulfide) materials suitable for injection molding and extrusion. 1.2?This classification system is not intended for the selection of materials, but only as a means to call out plastic materials to be used for the manufacture of parts. The selection of these materials shall be made by personnel with expertise in the plastics field where the environment, inherent properties of the materials, performance of the parts, part design, manufacturing process, and economics are considered. 1.3?The properties included in this classification system are those required to identify the compositions covered. If necessary, other requirements identifying particular characteristics important to specific applications shall be designated by using the suffixes given in Section 5 or Classification System D4000. 1.4?The values stated in SI units are to be regarded as the standard. Note 1:?There is no known ISO equivalent to this
standard.
Note 2:?ASTM Standard D6358 provides a classification system
for the same materials covered in this standard, along with
additional PPS materials, with the major difference being its use
of ISO test methods, versus the use of ASTM test methods in this
standard. The user of this standard is encouraged to evaluate
switching to the use of Standard D6358 as it is more up to date with
current practices.
1.5?This precautionary statement pertains only to the test method portion of this classification system, Section 12. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
