Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D4066-13(2019)
Standard Classification System for Nylon Injection and Extrusion Materials (PA)
Přeložit název
NORMA vydána dne 1.11.2019
Informace o normě:
Označení normy: ASTM D4066-13(2019)
Datum vydání normy: 1.11.2019
Kód zboží: NS-975361
Počet stran: 17
Přibližná hmotnost: 51 g (0.11 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D4066-13(2019) :
This classification system covers nylon injection and extrusion materials. Nylon materials are classified into groups according to their composition. Groups are further classified into classes and grades. Grades are identified by a single letter that indicates the reinforcement or filler used and two digits, in multiples of 5, which indicate the nominal quantity in weight percent. Specific requirements for variations of nylon materials shall be shown by a six-character designator. Suffixes shall be used for those properties not covered by basic requirements. Specific suffix requirements shall always take precedence over basic requirements. Tensile strength, flexural strength, Izod impact resistance, deflection temperature, and density shall be done on test pieces based on injection molded ISO 3167 type multipurpose test specimens. Conditioning, preparation, testing, inspection, packaging, and marking shall be in conformance to the requirements in this standard classification system.
Keywords:
classification, classification system, line callout, plastic materials,, ICS Number Code 83.080.20 (Thermoplastic materials)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This classification system covers nylon materials suitable for injection molding and extrusion. Some of these compositions are also suitable for compression molding and application from solution. 1.2 The properties included in this classification system are those required to identify the compositions covered. There may be other requirements necessary to identify particular characteristics important to specialized applications. These may be specified by using the suffixes as given in Section 5. 1.3 This classification system and subsequent line call-out (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 The following precautionary caveat pertains only to the test methods portion, Section 11, of this classification system. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1: There is no known ISO equivalent to this
standard.
Note 2: This classification system is being revised to include
international 4-mm specimens and test procedures as the standard
for compliance. The 3.2-mm specimens; test methods; and Tables PA,
A, and B are included in Appendix
X3 as a reference for those wishing to use them. It is
recommended that the material manufacturer be consulted on all
call-outs against this classification system.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace zákonů
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
