Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM D3935-09

Standard Specification for Polycarbonate (PC) Unfilled and Reinforced Material

Automaticky přeložený název:

Standard Specification pro polykarbonát (PC), neobsazených a materiálu vyztuženého

NORMA vydána dne 15.4.2009

Jazyk
Provedení	PDF - okamžité stažení - 2 010.10 Kč Tištěné - 2 010.10 Kč
Dostupnost	SKLADEM
Cena	2010.10 Kč bez DPH
2 010.10 Kč

Informace o normě:

Označení normy: ASTM D3935-09
Poznámka: NEPLATNÁ
Datum vydání normy: 15.4.2009
Kód zboží: NS-25387
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Anotace textu normy ASTM D3935-09 :

Keywords:

line-callout specification, plastics, polycarbonate resins, recycled plastics, specification, Polycarbonate (PC)--specifications, Polymers--specifications, Recycled plastics--specifications, Extrusion compounds (plastic)--specifications, Line call-out specifications--plastics, Molding/extrusion compounds/materials--specifications, Plastics--specifications, ICS Number Code 83.080.20 (Thermoplastic materials), 83.120 (Reinforced plast)

Doplňující informace

1. Scope

1.1 This specification covers unfilled and reinforced polycarbonate and polycarbonate copolymer materials suitable for injection molding, blow molding, and extrusion. Some of these compositions may also find use for compression molding or application from solution.

1.2 The properties in this specification are those required for identifying the compositions covered. There may be other requirements necessary for identifying particular characteristics important to specific applications. Those may be specified by using the suffixes in accordance with Section 5.

1.3 The values stated in SI units are to be regarded as the standard.

Note 1—This specification and ISO 7391-1 and ISO 7391-2 address the same subject matter, but differ in technical content.

1.4 The following hazards caveat pertains only to the test methods portion, Section 12, of this specification. This standard does not purport to address all safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability or regulatory limitations prior to use.

2. Referenced Documents

D648-18	Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
E169-16(2022)	Standard Practices for General Techniques of Ultraviolet-Visible Quantitative Analysis
D256-23e1	Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics (Includes all amendments and changes 4/7/2023).
D638-22	Standard Test Method for Tensile Properties of Plastics
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
D7209-06	Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products (Withdrawn 2015)
D5630-22	Standard Test Method for Ash Content in Plastics
D4000-23	Standard Classification System for Specifying Plastic Materials
D3892-15(2020)	Standard Practice for Packaging/Packing of Plastics
ISO?7391-2	Plastics--Polycarbonate Molding and Extrusion Materials (Part 2: Preparation of Test Specimens and Determination of Properties)
ISO?7391-1	Plastics--Polycarbonate Molding and Extrusion Materials (Part 1: Designation--2006)
D2584-18	Standard Test Method for Ignition Loss of Cured Reinforced Resins
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1238-23a	Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer (Includes all amendments and changes 12/6/2023).
D792-20	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D790-17	Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D883-24	Standard Terminology Relating to Plastics

Doporučujeme:

EviNor - Řízení a aktualizace českých norem

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.