Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM D2673-14(2022)
Standard Specification for Oriented Polypropylene Film
Přeložit název
NORMA vydána dne 15.3.2022
Informace o normě:
Označení normy: ASTM D2673-14(2022)
Datum vydání normy: 15.3.2022
Kód zboží: NS-1051682
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM D2673-14(2022) :
This specification covers uniaxially, biaxially, or balanced oriented polypropylene (OPP) films in a specified thickness range. Films can contain colorants, stabilizers, or other additives, and can be coated for the improvement of performance properties such as heat sealability, gas permeability, and so forth. Films can also be annealed (heat-set) to reduce the unrestrained linear shrinkage and shrink tension on exposure to heat. The base polymer shall be a Group 1 or 2 polypropylene (PP), or a blend of such with one or more other polymers, provided the PP fraction is the main component. Films shall adhere to physical requirements as defined for appearance, blocking, thickness, package yield, width, length, and requirements for those intended for the packaging of food, drugs, and cosmetics. For characterization purposes, this specification provides a cell classification based on six performance parameters characterized by a code designation (1 to 6), as follows: (1) coefficient of friction; (2) unrestrained linear thermal shrinkage; (3) wetting tension; (4) heat-sealability; (5) gloss; (6) haze.
Keywords:
balanced oriented PP film, biaxially oriented PP film, oriented polypropylene film, uniaxially oriented PP film,, ICS Number Code 83.140.10 (Films and sheets)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||
|
1.1?This specification covers oriented polypropylene (OPP) film in the thickness range from 10 to 75 ?m (0.4 to 3.0 mils). 1.2?The film can contain colorants, stabilizers, or other additives, and can be coated for the improvement of performance properties (heat sealability, gas permeability, and so forth). 1.3?The film can be annealed (heat-set) to reduce the unrestrained linear shrinkage and shrink tension on exposure to heat. 1.4?The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.5?The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1:?There is no known ISO equivalent to this
standard.
1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace zákonů
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
