Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

NEPLATNÁ ASTM D1828-01(2013) 1.7.2013 náhled

Doplňující informace

ASTM D1828-01(2013)

Standard Practice for Atmospheric Exposure of Adhesive-Bonded Joints and Structures

Automaticky přeložený název:

Standardní praktiky pro atmosférickým vlivům lepidlem lepených spojů a konstrukcí

NORMA vydána dne 1.7.2013

Jazyk
Provedení	PDF - okamžité stažení - 1 536.70 Kč Tištěné - 1 536.70 Kč
Dostupnost	SKLADEM
Cena	1 536.70 Kč bez DPH
1 536.70 Kč

Informace o normě:

Označení normy: ASTM D1828-01(2013)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.7.2013
Kód zboží: NS-18491
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Lepidla

Anotace textu normy ASTM D1828-01(2013) :

Keywords:
adhesive bonded joints, adhesive bonded structures, adhesives, atmospheric exposure, weathering, ICS Number Code 83.180 (Adhesives)

Doplňující informace

Significance and Use

4.1 The atmospheric exposure tests described in this practice will evaluate the stability of the adhesive bond only in terms of a particular natural atmosphere. Since the atmospheric conditions vary greatly from year to year, these results will not be as reproducible as those derived from laboratory aging procedures. Considerable research has shown that laboratory artificial weathering tests will not give consistently good correlation with outdoor test exposures (2, 3, 4).

1. Scope

1.1 This practice covers the procedure for the direct exposure of adhesive bonded joints and structures to natural atmospheric environments.

1.2 The procedure for sheltered atmospheric exposure, such as a Stevenson screen (1),² of adhesive-bonded joints and specimens is the same except for the requirements of facing south and measurement of solar radiation.

1.3 This practice is limited to the procedure by which samples are exposed and does not cover the tests that may be used to evaluate the effects of atmospheric exposure on these adhesive-bonded joints and structures. These samples could be any one of several varieties.

1.3.1 A complete structure for test,

1.3.2 A section of a structure for test,

1.3.3 A complete structure or section with strength observations on specimens cut therefrom,

1.3.4 Test specimens themselves, or

1.3.5 Any of the above, mounted under stress.

1.4 Suitable test methods for evaluation of the effects of exposure include nondestructive qualitative or quantitative observations on the same sample at prescribed intervals, or destructive tests on separate sets of specimens in accordance with such tests as Test Method D1002.

1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

	ASTM Standard Racks and Pipe Frames Blueprints Blueprints of ASTM standard racks and pipe frames may be obtained from ASTM International Headquarters. Order Adjunct No. . Original adjunct produced in 1957.
D897-08(2016)	Standard Test Method for Tensile Properties of Adhesive Bonds
D896-04(2017)	Standard Practice for Resistance of Adhesive Bonds to Chemical Reagents
D1002-10(2019)	Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
D907-15(2023)	Standard Terminology of Adhesives