Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM C150/C150M-19a
Standard Specification for Portland Cement (Includes all amendments And changes 4/22/2020).
Přeložit název
NORMA vydána dne 12.4.2019
Informace o normě:
Označení normy: ASTM C150/C150M-19a
Poznámka: NEPLATNÁ
Datum vydání normy: 12.4.2019
Kód zboží: NS-946434
Počet stran: 10
Přibližná hmotnost: 30 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM C150/C150M-19a :
Keywords:
hydraulic cement, portland cement, specification,, ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers ten types of portland cement, as follows (see Note 2): 1.1.1 Type I—For use when the special properties specified for any other type are not required. 1.1.2 Type IA—Air-entraining cement for the same uses as Type I, where air-entrainment is desired. 1.1.3 Type II—For general use, more especially when moderate sulfate resistance is desired. 1.1.4 Type IIA—Air-entraining cement for the same uses as Type II, where air-entrainment is desired. 1.1.5 Type II(MH)—For general use, more especially when moderate heat of hydration and moderate sulfate resistance are desired. 1.1.6 Type II(MH)A—Air-entraining cement for the same uses as Type II(MH), where air-entrainment is desired. 1.1.7 Type III—For use when high early strength is desired. 1.1.8 Type IIIA—Air-entraining cement for the same use as Type III, where air-entrainment is desired. 1.1.9 Type IV—For use when a low heat of hydration is desired. 1.1.10 Type V—For use when high sulfate resistance is desired. Note 1: Some cements are designated with a combined type
classification, such as Type I/II, indicating that the cement meets
the requirements of the indicated types and is being offered as
suitable for use when either type is desired.
Note 2: Cement conforming to the requirements for all types
are not carried in stock in some areas. In advance of specifying
the use of cement other than Type I, determine whether the proposed
type of cement is, or can be made, available.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
