Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation
Automaticky přeložený název:
Standardní specifikace pro PA flexibilní mobilní tepelné a zvukově izolační izolace
NORMA vydána dne 1.9.2012
Označení normy: ASTM C1482-12
Poznámka: NEPLATNÁ
Datum vydání normy: 1.9.2012
Kód zboží: NS-11487
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
flexible cellular insulation, pipe insulation, polyimide, ship insulation, sound absorbing, thermal insulation, ICS Number Code 91.100.60 (Thermal and sound insulating materials)
1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
1.1 This specification covers the composition and physical properties of lightweight, flexible open-cell polyimide foam insulation intended for use as thermal and sound-absorbing insulation for temperatures from -328°F up to +572°F (-200°C and +300°C) in commercial and industrial environments. 1.1.1 Annex A1 includes faced polyimide foam as specified by the U.S. Navy for marine applications. 1.1.2 This standard is designed as a material specification and not a design document. Physical property requirements vary by application and temperature. No single test is adequate for estimating either the minimum or maximum use temperature of polyimide foam under all possible conditions. Consult the manufacturer for specific recommendations and physical properties for specific applications. 1.1.3 The use of an appropriate vapor retarder is required in all applications where condensation could occur and cause a decrease in thermal performance or affect other system properties. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions. 1.4 This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
|
|
Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
|
|
Standard Test Method for Measuring Compressive Properties of Thermal Insulations
|
|
Standard Terminology Relating to Thermal Insulation
|
|
Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus (Includes all amendments and changes 2/23/2023).
|
|
Standard Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation
|
|
Standard Test Method for Steady-State Heat Transfer Properties of Pipe Insulation
|
|
Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
|
|
Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
|
|
Standard Test Method for Tumbling Friability of Preformed Block-Type and Preformed Pipe-Covering-Type Thermal Insulation
|
|
Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
|
|
Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings
|
|
Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
|
|
Standard Terminology Relating to Building and Environmental Acoustics
|
|
Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing
|
|
Standard Test Method for Tensile Properties of Plastics
|
|
Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials (Includes all amendments and changes 9/16/2021).
|
DOD-E-24607
|
Enamel, Interior, Nonflaming (Dry), Chlorinated Alkyd Resin, Semigloss (Metric)
|
|
Standard Guide for Measurement of Gases Present or Generated During Fires
|
|
Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
|
|
Standard Test Method for Surface Burning Characteristics of Building Materials (Includes all amendments and changes 1/29/2024).
|
|
Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
|
|
Standard Terminology of Fire Standards
|
|
Standard Practices for Mounting Test Specimens During Sound Absorption Tests
|
|
Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics
|
|
Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
|
|
Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials
|
|
Standard Test Method for Determining Wicking of Fibrous Glass Blanket Insulation (Aircraft Type)
|
|
Standard Test Methods for Rubber Property´Compression Set
|
|
Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging
|
|
Standard Test Methods for Flexible Cellular Materials´Slab, Bonded, and Molded Urethane Foams
|
|
Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source
|
|
Standard Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing
|
|
Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method
|
|
Standard Practice for Estimating the Maximum Use Temperature of Thermal Insulations
|
|
Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
Historická
15.5.2011
Historická
1.11.2010
Historická
1.5.2012
Historická
1.1.2014
Historická
15.4.2014
Historická
15.5.2013
Poslední aktualizace: 04.11.2024 (Počet položek: 2 209 323)
© Copyright 2024 NORMSERVIS s.r.o.