Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Norma ASTM B955/B955M-18 15.5.2018 náhled

Doplňující informace

ASTM B955/B955M-18

Standard Specification for Aluminum-Alloy Centrifugal Castings

Přeložit název

NORMA vydána dne 15.5.2018

Jazyk
Provedení	PDF - okamžité stažení - 1 635.80 Kč PDF + redline - ihned - 1 962.90 Kč Tištěné - 1 635.80 Kč Tisk + redline - 1 962.90 Kč
Dostupnost	SKLADEM
Cena	1 635.80 Kč bez DPH
1 635.80 Kč

Informace o normě:

Označení normy: ASTM B955/B955M-18
Datum vydání normy: 15.5.2018
Kód zboží: NS-849366
Počet stran: 11
Přibližná hmotnost: 33 g (0.07 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Výrobky z hliníku

Anotace textu normy ASTM B955/B955M-18 :

This specification covers the standard for aluminum-alloy centrifugal castings. This specification does not cover aluminum-alloy centrifugal castings used in aerospace applications. The castings shall be in accordance to the prescribed chemical composition. Chemical composition shall be determined by analyzing samples at the time the castings are poured, or samples taken from castings or tension test specimens. Unless otherwise stated, the tensile strength, yield strength and elongation of test specimens cut from casting shall be in accordance with the standards prescribed herein. If the specimens fail to conform to tension requirements, test bars representative of the castings may be retested in accordance with the replacement tests and retest provisions.

Keywords:
aluminum, centrifugal castings,, ICS Number Code 77.150.10 (Aluminium products)

Doplňující informace

1. Scope

1.1 This specification covers aluminum-alloy centrifugal castings designated as shown in Table 1.

1.2 This specification is for aluminum-alloy centrifugal castings used in general purpose applications. It may not address the mechanical properties, integrity testing, and verification required for highly loaded or safety critical applications.

1.3 Alloy and temper designations are in accordance with ANSI H35.1/H35.1 (M).

1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.

1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.

1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

E165-09	Standard Practice for Liquid Penetrant Examination for General Industry
H35.1/H35.1 (M)	American National Standard Alloy and Temper Designation Systems for Aluminum
B557M-15(2023)	Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)
B660-23	Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
B881-17	Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products
B917/B917M-12(2020)	Standard Practice for Heat Treatment of Aluminum-Alloy Castings From All Processes
B985-12(2016)	Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis
D3951-18(2023)	Standard Practice for Commercial Packaging
B179-18	Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes
B275-14	Standard Practice for Codification of Certain Zinc, Tin and Lead Die Castings (Withdrawn 2020)
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34-11	Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E94-04	Standard Guide for Radiographic Examination
E155-20	Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E607-02	Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere
E716-16(2021)e2	Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry (Includes all amendments and changes 9/7/2022).
E1251-17a	Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry (Includes all amendments and changes 10/26/2017).
E2422-22	Standard Digital Reference Images for Inspection of Aluminum Castings
Z1.4	Sampling Procedures and Tables for Inspection by Attributes
B557-15(2023)	Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products

Doporučujeme:

nody.cz - Splňte si svůj sen o vlatsním e-shopu

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.