Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM B686/B686M-18
Standard Specification for Aluminum Alloy Castings, High-Strength
Přeložit název
NORMA vydána dne 15.5.2018
Informace o normě:
Označení normy: ASTM B686/B686M-18
Datum vydání normy: 15.5.2018
Kód zboží: NS-851265
Počet stran: 12
Přibližná hmotnost: 36 g (0.08 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM B686/B686M-18 :
This specification covers aluminum-alloy high-strength castings in the following designations: A12010, A03540, A33550, A13560, and A13570. Castings covered by this specification are intended for use in airframe, missile, and other critical applications where high strength, ductility, and sound castings are required. Castings shall be classified by inspection classes: Class 1, Class 2, Class 3, and Class 4 and shall be specified as Grade A, Grade B, Grade C, or Grade D based on radiographic quality. Requirements for the casting process, chemical composition analysis, preproduction sample, radiographic soundness and mechanical property control (including foundry control and acceptance procedure), heat treatment, tensile testing, and dimensions are detailed. The castings shall conform to the chemical composition prescribed for silicon, iron, copper, manganese, magnesium, zinc, titanium, and aluminum, and to the specified mechanical properties such as tensile strength, yield strength and elongation.
Keywords:
aluminum, high strength, sand casting,, ICS Number Code 77.150.10 (Aluminium products)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers aluminum-alloy high-strength castings designated as shown in Table 1. 1.2 Castings covered by this specification are intended for use in airframe, missile, and other critical applications where high strength, ductility, and sound castings are required. 1.3 Alloy and temper designations are in accordance with ANSI H35.1/H35.1 (M). 1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units. 1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2. 1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
