Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM B474-03(2009)
Standard Specification for Electric Fusion Welded Nickel and Nickel Alloy Pipe
Automaticky přeložený název:
Standardní specifikace pro Electric Fusion svařované Nikl a slitiny niklu Pipe
NORMA vydána dne 1.10.2009
Informace o normě:
Označení normy: ASTM B474-03(2009)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.10.2009
Kód zboží: NS-6824
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM B474-03(2009) :
Keywords:
fusion welded, high-temperature alloy, pipe, Carpenter alloy--specifications, Chromium-nickel-iron-molybdenum-copper alloy--pipe/tube, Corrosion--metals/alloys, Corrosion--pipe/tube materials/systems, Corrosive service applications--pipe (Ni/Ni alloy), Electric-fusion-welded Ni/Ni alloy pipe, High-temperature service applications--nickel (specifications), Nickel alloy pipe--specifications, Nickel-chromium alloys--specifications, Nickel-iron alloy--specifications
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers electric fusion welded pipe suitable for high-temperature or corrosive service as listed in Table 1. (Although no restrictions are placed on the sizes of pipe that may be furnished under this specification, commercial practice is commonly limited to sizes not less than 8 in. (203 mm) nominal diameter.) 1.2 Five classes of pipe are covered as follows: 1.2.1 Class 1—Pipe shall be double welded by processes employing filler metal in all passes and shall be completely radiographed. 1.2.2 Class 2—Pipe shall be double welded by processes employing filler metal in all passes. No radiography is required. 1.2.3 Class 3—Pipe shall be single welded by processes employing filler metal in all passes and shall be completely radiographed. 1.2.4 Class 4—Same as Class 3 except that the weld pass exposed to the inside pipe surface may be made without the addition of filler metal. 1.2.5 Class 5—Pipe shall be double welded by processes employing filler metal in all passes and shall be spot radiographed. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. TABLE 1 Recommended Heat Treatment
A Recommended temperatures—Different temperatures may be selected by either the purchaser or the manufacturer. B Set temperatures, ±25°F (±14°C). C Minimum set temperature. D Registered Trademark of Haynes International. E Heat treatment is highly dependent on intended service temperature — consult material manufacturer for specific heat treatments for end use temperature. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
