Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM B370-22

Standard Specification for Copper Sheet and Strip for Building Construction

Přeložit název

NORMA vydána dne 1.5.2022

Jazyk
Provedení	PDF - okamžité stažení - 1 490.80 Kč PDF + redline - ihned - 1 788.90 Kč Tištěné - 1 490.80 Kč Tisk + redline - 1 788.90 Kč
Dostupnost	SKLADEM
Cena	1 490.80 Kč bez DPH
1 490.80 Kč

Informace o normě:

Označení normy: ASTM B370-22
Datum vydání normy: 1.5.2022
Kód zboží: NS-1058360
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Výrobky z mědi

Anotace textu normy ASTM B370-22 :

This specification establishes the requirements for rolled copper sheets and strips in flat lengths or coils of ounce-weight thicknesses for roofing, flashing, gutters, downspouts, and general sheet metal work in building construction. Products produced to this specification are not intended for electrical applications. Materials are available in the following tempers: O60 (soft), H00 (cold-rolled), H01 (cold-rolled, high yield), H02 (half hard), H03 (three-quarter hard), and H04 (hard). Products shall be sampled and prepared, then tested accordingly to examine their conformance to dimensional (mass, thickness, length, width, weight, and straightness), mechanical (tensile and yield strength, and Rockwell hardness), chemical composition, and grain recrystallization requirements.

Keywords:
building construction, copper sheet, copper strip, downspouts, flashing, gutters, roofing, sheet/strip in flat lengths/coils for building construction,, ICS Number Code 77.150.30 (Copper products)

Doplňující informace

1. Scope

1.1?This specification establishes the requirements for rolled copper sheet and strip in flat lengths or coils in ounce-weight thicknesses for roofing, cladding, flashings, gutters, downspouts, and general sheet metal work for building construction.

1.1.1?Products produced to this specification are not intended for electrical applications.

1.2?UnitsThe values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Note 1:?Specification B101 is an associated specification for lead-coated copper sheets and strip for building construction.

1.3?The following hazard caveat pertains to the test methods portion, Section 16, of this specification

1.3.1?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

B101-22	Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction
B248-22	Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
B601-18a	Standard Classification for Temper Designations for Copper and Copper Alloys´Wrought and Cast (Includes all amendments and changes 10/24/2018).
B846-19a	Standard Terminology for Copper and Copper Alloys (Includes all amendments and changes 8/8/2019).
E478-08(2017)	Standard Test Methods for Chemical Analysis of Copper Alloys
E8-04	Standard Test Methods for Tension Testing of Metallic Materials
E112-13(2021)	Standard Test Methods for Determining Average Grain Size
E255-23	Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
E3-11(2017)	Standard Guide for Preparation of Metallographic Specimens

Doporučujeme:

Aktualizace zákonů

Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.