Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM B306-20

Standard Specification for Copper Drainage Tube (DWV)

Přeložit název

NORMA vydána dne 1.6.2020

Jazyk
Provedení	Online zabezpečené PDF - 1 831.00 Kč Tištěné - 1 831.00 Kč
Dostupnost	SKLADEM
Cena	1831.00 Kč bez DPH
1 831.00 Kč

Informace o normě:

Označení normy: ASTM B306-20
Poznámka: NEPLATNÁ
Datum vydání normy: 1.6.2020
Kód zboží: NS-999917
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Neželezné kovové trubky

Anotace textu normy ASTM B306-20 :

Keywords:

drainage tube, sanitary tube, seamless copper tube, vent tube, waste tube,, ICS Number Code 23.040.15 (Non-ferrous metal pipes)

Doplňující informace

Significance and Use

17.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table and for dimensional tolerances, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29:

Property	Rounded Unit for Observed or Calculated Value

Chemical composition	nearest unit in the last right-hand place of
Hardness	figures of the specified limit

Tensile strength	nearest ksi (5 MPa)

1. Scope

1.1 This specification establishes the requirements for seamless copper tube (DWV) produced from Copper UNS No. C12200 and intended for sanitary drainage, waste, and vent piping.

Note 1: Fittings used for soldered or brazed connections in drainage, waste, or vent systems are described in ASME Standards B16.23 and B16.29 and CSA Standard B158.1.

Note 2: The assembly of copper drainage, waste, and vent systems by soldering is described in Practice B828.

Note 3: Solders for joining copper drainage, waste, or vent systems are described in Specification B32. The requirement for acceptable fluxes for these systems are described in Specification B813.

1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following hazard statement pertains only to the test method(s) described in this specification:

1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

E255-23	Standard Practice for Sampling Copper and Copper Alloys for the Determination of Chemical Composition
B32-20	Standard Specification for Solder Metal
E243-18	Standard Practice for Electromagnetic (Eddy Current) Examination of Copper and Copper-Alloy Tubes
E62-89(1996)	Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E18-22	Standard Test Methods for Rockwell Hardness of Metallic Materials
B900-16(2022)	Standard Practice for Packaging of Copper and Copper Alloy Mill Products for U.S. Government Agencies
B828-23	Standard Practice for Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings
B813-16	Standard Specification for Liquid and Paste Fluxes for Soldering of Copper and Copper Alloy Tube
B16.23	Cast Copper Alloy Solder Joint Drainage Fittings--DWV
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E53-07	Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E8-04	Standard Test Methods for Tension Testing of Metallic Materials
B601-18a	Standard Classification for Temper Designations for Copper and Copper Alloys´Wrought and Cast (Includes all amendments and changes 10/24/2018).
B16.29	Wrought Copper and Copper Alloy Solder Joint Drainage Fittings--DWV

Doporučujeme:

EviNor - Řízení a aktualizace českých norem

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.