Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
Přeložit název
NORMA vydána dne 1.4.2019
Označení normy: ASTM B150/B150M-19
Datum vydání normy: 1.4.2019
Kód zboží: NS-945888
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
This specification establishes the requirements for rods, bars, and shapes of aluminum bronze with Copper Alloy UNS Nos. C61300, C61400, C61900, C62300, C62400, C63000, C63020, C63200, C64200, and C64210. Products shall be produced in tempers HR50, M10, M20, M30, O20, O25, O30, O32, TQ30, TQ50 and TQ55. Products shall be tested and shall conform to dimensional (mass, diameter, length, thickness, straightness, and edge contour), mechanical (tensile and yield strength, Rockwell hardness, and elongation), and chemical composition requirements. Products should also meet requirements under mercurous nitrate test, ammonia test, and piston finish.
Keywords:
aluminum bronze bar, aluminum bronze rod, aluminum bronze shapes, UNS Alloy No. C61300, UNS Alloy No. C61400, UNS Alloy No. C61900, UNS Alloy No. C62300, UNS Alloy No. C62400, UNS Alloy No. C63000, UNS Alloy No. C63020, UNS Alloy No. C63200, UNS Alloy No. C64200, UNS Alloy No. C64210,, ICS Number Code 77.150.10 (Aluminium products)
1. Scope | ||||||||||||||||||||||||
1.1 This specification establishes the requirements for aluminum bronze rod, bar, and shapes for Copper Alloys UNS Nos. C61300, C61400, C61900, C62300, C62400, C63000, C63020, C63200, C64200, and C64210. Note 1: Product intended for hot forging is described in
Specification B124/B124M.
Note 2: Warning—Mercury has
been designated by many regulatory agencies as a hazardous
substance that can cause serious medical issues. Mercury, or its
vapor, has been demonstrated to be hazardous to health and
corrosive to materials. Use caution when handling mercury and
mercury-containing products. See the applicable product Safety Data
Sheet (SDS) for additional information. The potential exists that
selling mercury or mercury-containing products, or both, is
prohibited by local or national law. Users must determine legality
of sales in their location.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||
|
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
Poslední aktualizace: 22.11.2024 (Počet položek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.