Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM A888-03

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

Automaticky přeložený název:

Standardní specifikace pro Hubless Litinová půdy potrubí a armatur pro sanitární a Storm Drain , odpadech , a Vent Potrubní Aplikace

NORMA vydána dne 10.7.2003

Jazyk
Provedení	Online zabezpečené PDF - 2 830.60 Kč Tištěné - 2 830.60 Kč
Dostupnost	SKLADEM
Cena	2830.60 Kč bez DPH
2 830.60 Kč

Informace o normě:

Označení normy: ASTM A888-03
Poznámka: NEPLATNÁ
Datum vydání normy: 10.7.2003
Kód zboží: NS-4651
Počet stran: 50
Přibližná hmotnost: 150 g (0.33 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Anotace textu normy ASTM A888-03 :

Keywords:

iron, soil, pipe, fittings´ gravity´ dimensional, tolerances, cast iron, ICS Number Code 23.040.01 (Pipeline components in general. Pipelines), 91.140.80 (Drainage systems)

Doplňující informace

1. Scope

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, principal dimensions, and dimensional tolerances for hubless cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.

1.2 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the requirements given herein.

1.2.1 Lengths:

	Figures
EDP Identification Numbers for Hubless Pipe	1
10 ft (3.0 m) in sizes 1 ½ , 2, 3, 4, 5, 6, 8, 10, 12, and 15 inch.	1, 2
Method of Specifying Fittings	3

1.2.2Fittings:

Quarter Bend	4
Quarter Bend, Reducing	5
Quarter Bend, With Side Opening	6
Quarter Bend, With Heel Opening	7
Quarter Bend, Tapped	8
Quarter Bend, Double	9
Quarter Bend, Long	10
Short Sweep	11
Long Sweep	12
Long Sweep, Reducing	13
Fifth Bend	14
Sixth Bend	15
Eighth Bend	16
Eighth Bend Long	17
Sixteenth Bend	18
Sanitary Tee	19
Sanitary Tee With Side Opening	20
Sanitary Tee With 2 in. Side Opening R or L/R and L	21
Sanitary Tee, New Orleans Special With Side Opening	22
Sanitary Tee With 45 Side Openings and New Orleans	23
Sanitary Special Tee Tapped	24
Sanitary Tapped Tee, Horizontal Twin	25
Sanitary Tapped Tee, Double Vertical	26
Y Branch	27
Y Branch, Double	28
Y Branch, Upright	29
Upright Y Wide Center Florida Special	30
Y Branch, Combination 1/8 Bend	31
Y Branch, Combination 1/8 Bend Double	32
Sanitary Cross	33
Sanitary Cross With Side Opening	34
Sanitary Cross, New Orleans, With Side Openings	35
Sanitary Cross, New Orleans, With 45 Special andRegular Side Openings	36
Sanitary Cross, Tapped	37
Test Tee	38
Tapped, Extension Piece	39
Increaser-Reducer	40
Increaser-Reducer, Short	41
Tapped Adapter	42
Blind Plug	43
Iron Body Cleanout-Tapped	44
P Trap	45
P Trap, Long	46
P Trap, Long-Tapped	47
P Trap, Deep Seal	48
P Trap, Reducing	49
P Trap, With Primer	50
P Trap, With Tapped Inlet	51
Hub Adapter	52
Tapped Inlet, Double	53
Modified Combination Wye and 1/8 Bend, Double	54
Modified Combination Wye and 1/8 Bend, Double, Extended	55
Regular or Extended Left or Right Regular or ExtendedDouble	56
Regular or Extended Left or Right Regular or ExtendedDouble	57
Two-Way Cleanout	58
Twin Cleanout	59
Closet Bend, Regular and Reducing	60
Closet Flange	61
Tapping Bosses	62

1.3 The values stated in inch-pound units shall be regarded as the standard. The values given in parentheses shall be for information only.

Note 1—The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

2. Referenced Documents

E1645-25	Standard Practice for Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis
D1248-25	Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
B1.20	Pipe Threads
A644-24	Standard Terminology Relating to Iron Castings

National Motor Freight Classification Rules Available from National Motor Freight Traffic Association, Inc. (NMFTA), 1001 N. Fairfax St., Suite 600, Alexandria, VA 22314-1798, http://www.nmfta.org.
E2349-26	Standard Practice for Safety Requirements in Metal Casting Operations: Sand Preparation, Molding, and Core Making; Melting and Pouring; and Cleaning and Finishing
D3960-25	Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
E8-04	Standard Test Methods for Tension Testing of Metallic Materials
MIL-STD-129	Military Marking for Shipment and Storage
A48/A48M-22	Standard Specification for Gray Iron Castings
Cast Iron Soil Pipe Institute (CISPI)	Specification 301 Available from Cast Iron Soil Pipe Institute (CISPI), 2401 Fieldcrest Dr., Mundelein, IL 60060, http://www.cispi.org.

Odebírejte informace o nově vydaných normách ZDARMA:

Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.