Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM A325-06

Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength

Automaticky přeložený název:

Standardní specifikace pro strukturální šrouby , oceli, zušlechtěné , 120/105 ksi Minimální pevnost v tahu

NORMA vydána dne 1.8.2006

Jazyk
Provedení	Online zabezpečené PDF - 1 806.90 Kč Tištěné - 1 806.90 Kč
Dostupnost	SKLADEM
Cena	1806.90 Kč bez DPH
1 806.90 Kč

Informace o normě:

Označení normy: ASTM A325-06
Poznámka: NEPLATNÁ
Datum vydání normy: 1.8.2006
Kód zboží: NS-2049
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Anotace textu normy ASTM A325-06 :

Keywords:

bolts, carbon steel, steel, structural, weathering steel, ICS Number Code 21.060.10 (Bolts, screws, studs)

Doplňující informace

1. Scope

1.1 This specification covers two types of quenched and tempered steel heavy hex structural bolts having a minimum tensile strength of 120 ksi for sizes 1.0 in. and less and 105 ksi for sizes over 1.0 to 11/2 in., inclusive.

1.2 The bolts are intended for use in structural connections. These connections are covered under the requirements of the Specification for Structural Joints Using ASTM A 325 or A 490 Bolts, approved by the Research Council on Structural Connections, endorsed by the American Institute of Steel Construction and by the Industrial Fastener Institute.

1.3 The bolts are furnished in sizes 1/2 to 11/2 in., inclusive. They are designated by type, denoting chemical composition as follows:

Type	Description
Type 1	Medium carbon, carbon boron, or medium carbon alloy steel.
Type 2	Withdrawn in November 1991.
Type 3	Weathering steel.

Note 1—Bolts for general applications, including anchor bolts, are covered by Specification A 449. Also refer to Specification A 449 for quenched and tempered steel bolts and studs with diameters greater than 11/2 in. but with similar mechanical properties.

Note 2

A complete metric companion to Specification A 325 has been developed-Specification A 325M; therefore, no metric equivalents are presented in this specification.

1.4 This specification is applicable to heavy hex structural bolts only. For bolts of other configurations and thread lengths with similar mechanical properties, see Specification A 449.

1.5 Terms used in this specification are defined in Terminology F 1789.

The following safety hazard caveat pertains only to the test methods portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

B695-21	Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
G101-04(2025)	Standard Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
F1136-10	Standard Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners
F606-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
A449-14(2020)	Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use
A325M-14	Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength (Metric) (Withdrawn 2016)
A194/A194M-26	Standard Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both
A751-25	Standard Test Methods and Practices for Chemical Analysis of Steel Products
D3951-18(2023)	Standard Practice for Commercial Packaging
F436-11	Standard Specification for Hardened Steel Washers
F788/F788M-20(2025)	Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series
F959-15	Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
B?1.1	Unified Screw Threads
B?18.2.6	Fasteners for Use in Structural Applications
B?18.24	Part Identification Number (PIN) Code System Standard for B18 Fastener Products
Specification for Structural Joints Using High-Strength Bolts
F1470-24	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
F1789-26	Standard Terminology for F16 Mechanical Fasteners
A563-15	Standard Specification for Carbon and Alloy Steel Nuts
F2329-13	Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners

Doporučujeme:

EviZak - všechny zákony včetně jejich evidence na jednom místě

Poskytování aktuálních informací o legislativních předpisech vyhlášených ve Sbírce zákonů od roku 1945.
Aktualizace 2x v měsíci !

Chcete vědět více informací? Podívejte se na tuto stránku.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.