Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
IEC 60730-2-10-ed.3.0
Automatic electrical controls - Part 2-10: Particular requirements for motor-starting relays
Přeložit název
NORMA vydána dne 12.8.2026
Informace o normě:
Označení normy: IEC 60730-2-10-ed.3.0
Datum vydání normy: 12.8.2026
Kód zboží: NS-1279915
Počet stran: 17
Přibližná hmotnost: 51 g (0.11 liber)
Země: Mezinárodní technická norma
Kategorie: Technické normy IEC
Kategorie - podobné normy:
Anotace textu normy IEC 60730-2-10-ed.3.0 :
IEC 60730-2-10:2026 applies to automatic electrical motor-starting relays - intended to control the start windings of single phase motors; - for use in, on, or in association with equipment for household appliance and similar use; NOTE 1 Throughout this document, the word "equipment" means "appliance and equipment" and "control" means "motor-starting relays". - intended for appliances within the scope of IEC 60335; - for equipment that is used in building automation within the scope of ISO 16484 series and IEC 63044 series (HBES/BACS); - for equipment that is used by the public, such as equipment intended to be used in shops, offices, hospitals, farms and commercial and industrial applications; EXAMPLE 1 Controls for commercial catering, heating and air-conditioning equipment. - used in, on, or in association with equipment that are smart enabled; EXAMPLE 2 Smart grid control, remote interfaces/control of energy-consuming equipment. - that are AC or DC powered with a rated voltage not exceeding 690 V AC or 600 V DC; - used in, on, or in association with equipment that use electricity, gas, oil, solid fuel, solar thermal energy, etc., or a combination thereof; - utilized as part of a control system or controls which are mechanically integral with multifunctional controls having non-electrical outputs; - using NTC or PTC thermistors, requirements for which are contained in Annex J; - that are mechanically or electrically operated, responsive to or controlling such characteristics as current and voltage, or combinations thereof; EXAMPLE 3 Centrifugal motor-starting devices. - as well as manual controls when such are electrically and/or mechanically integral with automatic controls. NOTE 2 Requirements for manually actuated mechanical switches not forming part of an automatic control are contained in IEC 61058-1-1. This document applies to - the inherent safety of motor-starting control, and - functional safety of motor-starting control and safety related systems (when required), - controls where the performance (for example the effect of EMC phenomena) of the product can impair the overall safety and performance of the controlled system, - the operating values, operating times, and operating sequences where such are associated with equipment safety, - motor-starting controls incorporating electronic devices, thermistor elements, thermal elements or magnetic elements. This document specifies the requirements for construction, operation and testing of automatic electrical motor-starting relays used in, on, or in association with an equipment. This document does not - apply to motor-starting relays designed exclusively for industrial process applications unless explicitly mentioned in the relevant equipment standard. However, this document can be applied to motor-start relays for equipment intended specifically for industrial applications in cases where no relevant safety standard exists; - take into account the response value of an automatic action of a control, if such a response value is dependent upon the method of mounting the control in the equipment. Where a response value is of significant purpose for the protection of the user, or surroundings, the value defined in the appropriate equipment standard or as determined by the manufacturer will apply; - apply to general purpose relays or to contactors and motor starters of the type covered by IEC 60947 series; apply to mechanically operated motor-starting devices This part 2-10 is intended to be used in conjunction with IEC 60730-1. It was established on the basis of the sixth edition of that standard (2022). Consideration may be given to future editions of, or amendments to, IEC 60730-1. This part 2-10 supplements or modifies the corresponding clauses in IEC 60730-1, so as to convert that publication into the IEC standard: Particular requirements for motor-starting relays. Where this part 2-10 states "addition", "modification" or "replacement", the relevant requirement, test specification or explanatory matter in Part 1 should be adapted accordingly. When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies. This third edition cancels and replaces the second edition published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) adoption of IEC 60730-1:2022 with all of its significant changes. LIEC 60730-2-10:2026 sapplique aux relais electriques automatiques de demarrage de moteur - destines a commander les enroulements de demarrage des moteurs monophases; - destines a etre utilises dans, sur ou avec des materiels pour appareils domestiques et a usage analogue; NOTE 1 Dans le present document, le terme "materiel" signifie "appareil et materiel" et le terme "dispositif de commande" signifie "relais de demarrage de moteur". - destines aux appareils relevant du domaine dapplication de lIEC 60335; - pour les materiels utilises dans lautomatisation des batiments relevant du domaine dapplication de la serie ISO 16484 et de la serie IEC 63044 (HBES/SGTB); - pour des materiels utilises par le public, tels que les materiels destines a etre utilises dans des magasins, des bureaux, des hopitaux, des fermes et des applications commerciales et industrielles; EXEMPLE 1 Dispositifs de commande pour les installations de restauration, de chauffage et dair conditionne. - utilises dans, sur ou avec des materiels actives intelligents; EXEMPLE 2 Dispositif de commande de reseau electrique intelligent, interfaces a distance/dispositif de commande de materiels consommateurs denergie. - qui sont alimentes en courant alternatif ou en courant continu avec une tension assignee qui ne depasse pas 690 V en courant alternatif ou 600 V en courant continu; - qui sont utilises dans, sur ou avec des materiels qui utilisent lelectricite, le gaz, le petrole, des combustibles solides, lenergie thermique solaire, etc. ou
Doporučujeme:
