Norma IEC 60034-14-ed.5.0-CMV 10.11.2026 náhled

IEC 60034-14-ed.5.0-CMV

Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity

Přeložit název

NORMA vydána dne 10.11.2026


Jazyk
Provedení
DostupnostSKLADEM
Cena7295.00 Kč bez DPH
7 295.00 Kč

Informace o normě:

Označení normy: IEC 60034-14-ed.5.0-CMV
Datum vydání normy: 10.11.2026
Kód zboží: NS-1290686
Počet stran: 36
Přibližná hmotnost: 108 g (0.24 liber)
Země: Mezinárodní technická norma
Kategorie: Technické normy IEC

Kategorie - podobné normy:

Elektrické rotační stroje obecně

Anotace textu normy IEC 60034-14-ed.5.0-CMV :

IEC 60034-14:2026 CMV contains both the official standard and its commented version. The commented version provides you with a quick and easy way to compare all the changes between IEC 60034-14:2026 edition 5.0 and the previous IEC 60034-14:2018 edition 4.0. Furthermore, comments from IEC TC 2 experts are provided to explain the reasons of the most relevant changes, or to clarify any part of the content. IEC 60034-14:2026 specifies the factory acceptance vibration test procedures and vibration limits for certain electrical machines under specified conditions, when uncoupled from any load or prime mover. It is applicable to DC and three-phase AC machines, with shaft heights 56 mm and higher and a rated output up to 50 MW, at operational speeds from 120 min–1 up to and including 15 000 min–1. This document is not applicable to machines mounted in situ (on site), three-phase commutator motors, single-phase machines, three-phase machines operated on single-phase systems, vertical waterpower generators, turbine generators greater than 20 MW and machines with magnetic bearings or series-wound machines. NOTE 1 For machines measured in situ, refer to applicable clauses or subclauses of ISO 20816-1 and ISO 20816-3. NOTE 2 For output power above 50 MW reference is made to the ISO 20816 series. NOTE 3 Vibration routine tests are not mandatory according to IEC 60034-1. If performed, the method for testing is included in this document. This fifth edition cancels and replaces the fourth edition published in 2018. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) subclause 6.3.3 Vertical machines: added two new subclauses: Type and routine tests; b) subclause 7.3 Test conditions: added two new subclauses: Direct-on-line and variable speed; c) Table 1: decreased limits for Grade A in free suspension for 56 <= H <= 132 mm; d) Clause 9 Limits of relative shaft vibration: added information how to mitigate effects of run-out on shaft vibration measurements.

Doporučujeme:

EviZak - všechny zákony včetně jejich evidence na jednom místě

Poskytování aktuálních informací o legislativních předpisech vyhlášených ve Sbírce zákonů od roku 1945.
Aktualizace 2x v měsíci !

Chcete vědět více informací? Podívejte se na tuto stránku.




Cookies Cookies

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.

Souhlas můžete odmítnout zde.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.