Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Test Method for Scratch Hardness of Materials Using a Diamond Stylus
Přeložit název
NORMA vydána dne 1.11.2017
Označení normy: ASTM G171-03(2017)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.11.2017
Kód zboží: NS-802856
Počet stran: 7
Přibližná hmotnost: 21 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
scratch, scratch hardness, single-point abrasion, stylus,, ICS Number Code 17.040.20 (Properties of surfaces)
Significance and Use | ||||
5.1 This test method is intended to measure the resistance of solid surfaces to permanent deformation under the action of a single point (stylus tip). It is a companion method to quasi-static hardness tests in which a stylus is pressed into a surface under a certain normal load and the resultant depth or impression size is used to compute a hardness number. Scratch hardness numbers, unlike quasi-static hardness numbers, involve a different combination of properties of the surface because the indenter, in this case a diamond stylus, moves tangentially along the surface. Therefore, the stress state under the scratching stylus differs from that produced under a quasi-static indenter. Scratch hardness numbers are in principle a more appropriate measure of the damage resistance of a material to surface damage processes like two-body abrasion than are quasi-static hardness numbers. 5.2 This test method is applicable to a wide range of materials. These include metals, alloys, and some polymers. The main criteria are that the scratching process produces a measurable scratch in the surface being tested without causing catastrophic fracture, spallation, or extensive delamination of surface material. Severe damage to the test surface, such that the scratch width is not clearly identifiable or that the edges of the scratch are chipped or distorted, invalidates the use of this test method to determine a scratch hardness number. Since the degree and type of surface damage in a material may vary with applied load, the applicability of this test to certain classes of materials may be limited by the maximum load at which valid scratch width measurements can be made. 5.3 The resistance of a material to abrasion by a single point may be affected by its sensitivity to the strain rate of the deformation process. Therefore, this test is conducted under low stylus traversing speeds. Use of a slow scratching speed also minimizes the possible effects of frictional heating. 5.4 This test uses measurements of the residual scratch width after the stylus has been removed to compute the scratch hardness number. Therefore, it reflects the permanent deformation resulting from scratching and not the instantaneous state of combined elastic and plastic deformation of the surface. |
||||
1. Scope | ||||
1.1 This test method covers laboratory procedures for determining the scratch hardness of the surfaces of solid materials. Within certain limitations, as described in this guide, this test method is applicable to metals, ceramics, polymers, and coated surfaces. The scratch hardness test, as described herein, is not intended to be used as a means to determine coating adhesion, nor is it intended for use with other than specific hemispherically-tipped, conical styli. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||
2. Referenced Documents | ||||
|
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
Poslední aktualizace: 22.11.2024 (Počet položek: 2 206 568)
© Copyright 2024 NORMSERVIS s.r.o.