Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Practice for Evaluating Microbial Susceptibility of Nonmetallic Materials by Laboratory Soil Burial
NORMA vydána dne 1.6.2009
Označení normy: ASTM G160-03(2009)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.6.2009
Kód zboží: NS-57477
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
biodegradeable, biological deterioration, defacement, disfigurement, fungal resistance, fungi, laboratory soil culture, microbial susceptibility, microbiological deterioration, mildew, mixed microbial innoculum, mold growth, soil environment, Laboratory soil/rock analysis, Microbiological examination, Nonmetallic materials, ICS Number Code 19.040 (Environmental testing)
Significance and Use | ||||
These results may be used to compare the susceptibility of materials when exposed to this test procedure. Microbiological susceptibility may be reflected by a number of changes including staining, weight loss, or reduction in tensile or flexural strength. This practice may be considered an inoculation with a mixed culture of fungi and bacteria. |
||||
1. Scope | ||||
1.1 This practice is limited to the method of conducting an evaluation of a nonmetallic material's microbiological susceptibility when in contact with the natural environment of the soil. This practice is intended for use on solid material test specimens that are no larger than approximately 2 cm (¾ in.) thick and 100 cm2 (20 in.2) or on film forming materials such as coatings which may be tested in the form of films at least 50 by 50 mm (2 by 2 in.) in size. This practice may be applied to articles that do not spend the majority of their service life in soil. 1.2 A wide variety of properties may be affected by microbial attack depending on material or item characteristics. Standard methods (where available) should be used for each different property to be evaluated. This practice does not attempt to enumerate all of the possible properties of interest nor specify the most appropriate test for those properties. Test methods must, however, be appropriate to the material being tested. 1.3 It is recommended that this practice be combined with appropriate environmental exposures (for example, sunlight simulating weathering devices, the hydrolytic effects of extended aqueous contact, or extraneous nutrients) or fabrication into articles (for example, adhesive bonding of seams) which may promote microbiological susceptibility during the service life of the material. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information purposes only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||
2. Referenced Documents | ||||
|
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
Poslední aktualizace: 12.01.2025 (Počet položek: 2 218 564)
© Copyright 2025 NORMSERVIS s.r.o.
Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.