Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners, Inch and Metric Series (Includes all amendments And changes 11/9/2023).
Přeložit název
NORMA vydána dne 1.12.2017
Označení normy: ASTM F959/F959M-17a
Poznámka: NEPLATNÁ
Datum vydání normy: 1.12.2017
Kód zboží: NS-808554
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Keywords:
compressible-washer-type, direct tension indicators, DTI, indicators,, ICS Number Code 21.060.01 (Fasteners in general)
1. Scope |
1.1 This specification covers the requirements for compressible-washer-type direct tension indicators, (DTIs) capable of indicating the achievement of a specified minimum tension in a structural bolting assembly. 1.2 Eight types of DTIs in nominal diameter sizes 1/2 through 1 1/2 in. as well as M16 through M36 are covered: 1.2.1 Type 325-1—DTIs for use with Specification F3125 Grade A325 Type 1 bolts or Grade F1852 assemblies. 1.2.2 Type 325–3—DTIs for use with Specification F3125 Grade A325 Type 3 bolts or Grade F1852 Type 3 assemblies. 1.2.3 Type 490–1—DTIs for use with Specification F3125 Grade A490 Type 1 bolts or Grade F2280 assemblies. 1.2.4 Type 490–3—DTIs for use with Specification F3125 Grade A490 Type 3 bolts Grade F2280 Type 3 assemblies. 1.2.5 Type 8.8-1—DTIs for use with Specification F3125 Grade A325M Type 1 bolts. 1.2.6 Type 8.8-3—DTIs for use with Specification F3125 Grade A325M Type 3 bolts. 1.2.7 Type 10.9-1—DTIs for use with Specification F3125 Grade A490M Type 1 bolts. 1.2.8 Type 10.9-3—DTIs for use with Specification F3125 Grade A490M Type 3 bolts. 1.3 DTIs are intended for installation with the protrusions against a hardened surface such as a bolt head, a hardened nut, or a hardened washer. (See Research Council on Structural Connections: Specification for Structural Joints Using High–Strength Bolts.) 1.4 This specification provides for furnishing Type 3 DTIs to a Chemical Composition Requirement or a Corrosion Resistance Index (CRI) at the manufacturer’s discretion. 1.5 Terms used in this specification are defined in Terminology F1789 unless otherwise specified. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 The following precautionary statement pertains only to the test method portions, Section 10 and Appendix X1 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
Poslední aktualizace: 22.12.2024 (Počet položek: 2 217 000)
© Copyright 2024 NORMSERVIS s.r.o.