ASTM F1698-02(2015)..
ASTM F1732-12
ASTM F1734-03(2009)..
ASTM F1741-08
ASTM F1743-08
ASTM F1760-01(2011)..
Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F949-15
Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings
Automaticky přeložený název:
Standardní specifikace pro poly (vinyl chloridu ) ( PVC) z vlnité kanalizační potrubí s hladkým vnitra a kování
NORMA vydána dne 1.4.2015
Informace o normě:
Označení normy: ASTM F949-15
Poznámka: NEPLATNÁ
Datum vydání normy: 1.4.2015
Kód zboží: NS-609012
Počet stran: 12
Přibližná hmotnost: 36 g (0.08 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM F949-15 :
Keywords:
ICS Number Code 23.040.20 (Plastic pipes), 23.040.45 (Plastic fittings)
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||
|
1.1 This specification covers requirements, test methods, and materials for 4 to 48 in. diameter poly(vinyl chloride) (PVC) corrugated pipe with a smooth interior. This profile wall pipe consists of an outer corrugated wall fused to a smooth inner wall providing pipe stiffness levels of 46 psi and 115psi. Joints and fittings are included in this specification. 1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use in nonpressure applications for sanitary sewers, storm sewers, and perforated and unperforated pipes for subdrainage. Note 1: Industrial waste disposal lines should be installed
only with the specific approval of the cognizant code authority,
since chemicals not commonly found in drains and sewers and
temperatures in excess of 140°F (60°C) may be
encountered.
1.3 Pipe and fittings produced to this specification shall be installed in accordance with Practice D2321. Note 2: For perforated pipe applications, the size of the
embedment zone and permeability of the embedment material are
important to the system's ability to provide the desired level of
infiltration or exfiltration. The gradation of the embedment
material must be compatible with the perforation slot size to avoid
backfill migration into the pipe.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following precautionary caveat pertains only
to the test method portion, Section 7, of this specification:
Standard Specification for Type PSM
Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings Standard Specification for Joints for
Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals Standard Terminology Relating to Plastic
Piping Systems Standard Specification for Elastomeric
Seals (Gaskets) for Joining Plastic Pipe Standard Specification for Poly(Vinyl
Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and
Fittings Standard Practice for Estimating the
Quality of Extruded Poly (Vinyl Chloride) (PVC) Pipe by the Heat
Reversion Technique Standard Practice for the Two-Step
(Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride)
(PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping
Components with Tapered Sockets Standard Specification for Solvent
Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems Standard Practice for Determination of
the Impact Resistance of Thermoplastic Pipe and Fittings by Means
of a Tup (Falling Weight) Standard Test Method for Determination of
External Loading Characteristics of Plastic Pipe by Parallel-Plate
Loading Standard Practice for Underground
Installation of Thermoplastic Pipe for Sewers and Other
Gravity-Flow Applications Standard Test Method for Adequacy of
Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded
Fittings by Acetone Immersion Standard Test Method for Determining
Dimensions of Thermoplastic Pipe and Fittings Standard Classification System and Basis
for Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds
and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds Standard Terminology for Abbreviated
Terms Relating to Plastics (Withdrawn 2024) Standard Practice for Conditioning
Plastics for Testing MIL-STD-129 Marking for Shipment and Storage AWWA Manual M45, Fiberglass Pipe Design Available from
American Water Works Association (AWWA), 6666 W. Quincy Ave.,
Denver, CO 80235, http://www.awwa.org. Fed. Std. No. 123 Marking for Shipments (Civil Agencies)
DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia,
PA 19111-5094 http://quicksearch.dla.mil/ |
Podobné normy:
Historická
1.3.2015
Historická
1.2.2012
Historická
1.8.2009
Historická
1.11.2008
Historická
1.11.2008
Historická
1.2.2011
Doporučujeme:
Aktualizace zákonů
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
