Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM F771-99

Standard Specification for Polyethylene (PE) Thermoplastic High-Pressure Irrigation Pipeline Systems

Automaticky přeložený název:

Standardní specifikace pro polyethylen ( PE ) Termoplastický vysokotlaké Zavlažovací Potrubní systémy

NORMA vydána dne 10.4.1999

Jazyk
Provedení	PDF - okamžité stažení - 2 020.00 Kč Tištěné - 2 020.00 Kč
Dostupnost	SKLADEM
Cena	2 020.00 Kč bez DPH
2 020.00 Kč

Informace o normě:

Označení normy: ASTM F771-99
Poznámka: NEPLATNÁ
Datum vydání normy: 10.4.1999
Kód zboží: NS-56399
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Anotace textu normy ASTM F771-99 :

Keywords:

Irrigation piping, Land drainage piping systems, polyethylene (PE) thermoplastic high-pressure irrigation pipeline, systems-classifying materials/identifying requirements, spec.,, Polyethylene (PE) pipe, high-pressure irrigation pipeline systems-classifying, materials/identifying requirements, spec.,,Order Form, ICS Number Code 23.040.20 (Plastic pipes)

Doplňující informace

1. Scope

1.1 This specification covers polyethylene (PE) thermoplastic pipelines used to convey, at rated pressures of 80 to 200 psi, water that is to be used for irrigation purposes. This specification includes criteria for classifying the pipe materials, a system of nomenclature for plastic pipe, requirements for pipe, test methods, joints, fittings, certification, and marking.

1.2 The values stated in inch-pound units are to be regarded as the standard.

1.3 The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

Fed. Std. No. 123	Marking for Shipment (Civil Agencies) Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
MIL-STD-129	Marking for Shipment and Storage
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
D1599-18	Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings
D1598-23	Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
D1505-18	Standard Test Method for Density of Plastics by the Density-Gradient Technique
D1248-16	Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable
D1238-23a	Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer (Includes all amendments and changes 12/6/2023).
D2609-21	Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe
D2683-20	Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
D2837-22	Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
D3035-22	Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
D3261-24	Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
F412-23	Standard Terminology Relating to Plastic Piping Systems
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2239-22	Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter

Doporučujeme:

EviNor - Řízení a aktualizace českých norem

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.