Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM F406-13

Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards

Automaticky přeložený název:

Standard Specification Consumer Safety pro Non-plné velikosti, dětské postýlky pro / rejdišti

NORMA vydána dne 1.5.2013

Jazyk
Provedení	PDF - okamžité stažení - 2 705.60 Kč Tištěné - 2 705.60 Kč
Dostupnost	SKLADEM
Cena	2 705.60 Kč bez DPH
2 705.60 Kč

Informace o normě:

Označení normy: ASTM F406-13
Poznámka: NEPLATNÁ
Datum vydání normy: 1.5.2013
Kód zboží: NS-55192
Počet stran: 41
Přibližná hmotnost: 123 g (0.27 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Anotace textu normy ASTM F406-13 :

Keywords:
non-full-size crib, playpen, play yard, ICS Number Code 97.190 (Equipment for children)

Doplňující informace

1. Scope

1.1 This consumer safety specification establishes testing requirements for structural integrity and performance requirements for non-full-size cribs/play yards, both rigid sided and mesh/fabric assemblies. It also provides requirements for labeling and instructional material. The term unit or product will refer to a non-full-size crib/play yard.

1.2 This specification covers a framed enclosure with a floor made for the purpose of providing sleeping and playing accommodations for a child who cannot climb out and is less than 35 in. (890 mm) in height. It also covers bassinet, changing table, or similar accessories to a non-full size crib/play yard. These accessories shall also comply with the applicable requirements of ASTM standards addressing those accessories. For example, a changing table that attaches to a play yard shall also comply with the applicable requirements in Specification F2388. This specification does not cover inflatable products.

1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Title

Section

Scope

Referenced Documents

ASTM Standards

2.1

Federal Regulations

2.4

Terminology

Definitions of Terms Specific to This Standard

3.1

Conspicuous

3.1.4

Cord

3.1.5

Corner Post

3.1.6

Dropside/Dropgate

3.1.7

Dynamic Load

3.1.8

Fabric

3.1.9

Foldable Side or End

3.1.10

Key Structural Elements

3.1.11

Manufacturer's Recommended Use Position

3.1.12

Mattress

3.1.13

Mesh

3.1.14

Mesh/Fabric Crib

3.1.15

Nonpaper Label

3.1.18

Occupant

3.1.19

Paper Label

3.1.20

Play Yard

3.1.21

Protrusion

3.1.22

Rigid Sided Crib

3.1.23

Seam

3.1.24

Static Load

3.1.25

Stationary Side

3.1.26

Structural Failure

3.1.28

Calibration and Standardization

General Requirements

Corner Posts

5.1

Scissoring, Shearing, or Pinching

5.6

Latching and Locking Mechanisms

5.8

Openings

5.9

Protective Components

5.10

Labeling

5.11

Stability

5.12

Cord/Strap Length

5.13

Coil Springs

5.14

Entrapment in Accessories

5.15

Mattress

5.16

Mattress for Rigid Sided Products

5.17

Protrusions

5.18

Bassinet/Cradle Accessories – Missing
Accessory Attachment Components

Record Keeping

5.20

Performance Requirements for Rigid Sided Units

Crib-Side Height

6.2

Spacing of Unit Components

6.3

Hardware

6.4

Fasteners

6.5

Construction and Finishing

6.6

Requirements for Cutouts

6.7

Plastic Teething Rail

6.11

Cyclic Test

6.12

Side(s) or End(s) Latch Testing, or Both

6.13

Dropgate Latch Testing

6.13.1

Foldable Side or End Latch Testing

6.13.2

Mattress Support System Vertical Impact Test
Requirements

Mattress Support System Testing

6.15

Crib Side Test Requirements

6.16

Spindle/Slat Strength Testing

6.17

Performance Requirements for Mesh/Fabric Units

Height of Sides

7.2

Side Deflection and Strength

7.3

Floor Strength

7.4

Top Rail Covering Material

7.5

Mesh Requirements

7.6

Mesh Openings

7.6.1

Mesh Strength

7.6.2

Fabric Material Requirements

7.7

Fabric Strength

7.7.1

Mesh/Fabric Assembly Requirements

7.8

Sewn Assembly

7.8.1

Seam Strength

7.8.2

Mesh/Fabric Attachment Strength

7.8.3

Mattress Vertical Displacement

7.9

Top Rail Configuration

7.10

Doporučujeme:

nody.cz - Splňte si svůj sen o vlatsním e-shopu