Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F3363-19
Standard Specification for Unvented Liquid/Gel Fuel-Burning Portable Devices
Přeložit název
NORMA vydána dne 15.2.2019
Informace o normě:
Označení normy: ASTM F3363-19
Datum vydání normy: 15.2.2019
Kód zboží: NS-937641
Počet stran: 5
Přibližná hmotnost: 15 g (0.03 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM F3363-19 :
Keywords:
carbon monoxide production, combustible liquid fuel, decorative fireplace, ethanol burner, fire pot, fire test, flame mitigation device, flammable liquid fuel, indoor usage test, indoor use, non-refillable canister, oxygen reduction, portable fireplace, stability test, table top fireplace,, ICS Number Code 97.100.99 (Heaters using other sources of energy)
Doplňující informace
| 1. Scope |
|
1.1 These requirements apply to devices that: 1.1.1 Sustain a flame over the fuel surface in an open reservoir; 1.1.2 Sustain a flame that does not require external ventilation to remove the combustion emissions, and are therefore ventless; 1.1.3 Burn a liquid, gelled, or otherwise non-solid fuel in an open reservoir or from a disposable, non-refillable, fuel container; 1.1.4 Have a fuel capacity of 2.5 L (0.67 gal) or less; 1.1.5 Have a power output of 1.47 kW (5000 BTU/h) or less; 1.1.6 Are intended to be easily carried or moved by hand; and 1.1.7 Are intended for indoor use, outdoor use, or both. 1.2 These requirements do not apply to devices that: 1.2.1 Are candles; 1.2.2 Are intended to cook or warm food; 1.2.3 Burn solid fuels, as determined by the test method described in Test Methods D4359; or 1.2.4 Do not have an open reservoir such as a refillable oil lamp, outdoor garden, or table torch intended to burn combustible fuel using a wick to sustain the flame (see Appendix X1). 1.3 This specification prescribes minimum safety requirements for devices to help ensure a reasonable degree of safety for normal use, thereby improving personal safety and reducing fires, deaths, and injuries. 1.4 This specification is not intended to replace other safety practices such as adult supervision, close monitoring of product when in use, and fire detection, alarm, or suppression systems. 1.5 The values stated in SI units are to be considered standard. The values in parentheses are explanatory or approximate information. 1.6 This specification is used to measure and describe the response of materials, products, or assemblies to heat, flame, and forces under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
