Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F3152-15
Standard Test Method for Determining Abrasion Resistance of Inks and Coatings on Substrates Using Norman Tool “WA-1010 Wet Abrader”
Automaticky přeložený název:
Standardní testovací metoda pro stanovení odolnosti proti oděru, inkoustů a nátěrů na podklady Použití Norman nástroj 'WA - 1010 Wet Abrader'
NORMA vydána dne 1.7.2015
Informace o normě:
Označení normy: ASTM F3152-15
Poznámka: NEPLATNÁ
Datum vydání normy: 1.7.2015
Kód zboží: NS-614666
Počet stran: 3
Přibližná hmotnost: 9 g (0.02 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Anotace textu normy ASTM F3152-15 :
Keywords:
The sole source of supply of the apparatus known to the committee at this time is Norman Tool Co., 15415 Old State Road, Evansville, IN 47725. If you are aware of alternative suppliers, please provide this information to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. , abrasion, breakthrough, coatings, inks, Innowet Abrex, membrane switch, Norman Tool, RCA, Taber,
Doplňující informace
| Significance and Use |
|
3.1 Membrane switch keys are subjected to repeated actuations, usually by a human finger. This can transfer body oil, hand creams, automotive fluids and so forth. Materials are often subjected to other conditions (for example, wiping, cleaning, rubbing) during handling, end-use, shipment, or storage that may cause abrasion damage. The result may be a significant removal of the coatings, text, or decorative inks. 3.2 This test method is applicable to a wide range of materials. The main criterion is that the abrasion process produces visible wear or breakthrough of the surface being tested. 3.3 The amount of abrasion damage to a surface is dependent on numerous variables. This test method provides a way of comparing relative abrasion resistance and the effect of chemicals on inks, coatings, and substrates. In no way do the results provide a correlation value of the number of human finger touches before coating failure. It only provides a means to compare results of tests performed using the same equipment, abrasive materials and loading conditions. 3.4 The test method can be used for quality control purposes, as a research and development tool, to evaluate material combinations for a given application, or for the comparison of materials with relatively similar properties and the effect of chemicals on the abrasion resistance. |
| 1. Scope |
|
1.1 This test method describes the procedure for subjecting inks or coatings on membrane switches to an abrasive medium, with or without the application of chemicals, at a specified force. 1.2 Within certain limitations, as described in this standard, this test method is applicable for materials including, but not limited to: printed or coated polyester, polycarbonate, and silicone rubber. The samples can be either flat or contoured. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
Odebírejte informace o nově vydaných normách ZDARMA:
Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.
