Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F3122-14(2022)
Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes
Přeložit název
NORMA vydána dne 1.4.2022
Informace o normě:
Označení normy: ASTM F3122-14(2022)
Poznámka: NEPLATNÁ
Datum vydání normy: 1.4.2022
Kód zboží: NS-1053525
Počet stran: 6
Přibližná hmotnost: 18 g (0.04 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM F3122-14(2022) :
Keywords:
anisotropic, Barcol, bearing pin, bearing strength, bearing test, bend testing, Brinell hardness, Charpy, Chevron-shaped-notch, chord modulus, compression testing, crack-arrest fracture toughness, crack formation, crack growth, crack-tip opening displacement, CTOD, dynamic elastic properties, Elastic modulus, fatigue life, fatigue testing, force-controlled, fracture toughness, hardness, hardness conversion, impact testing, inelastic, Izod, Knoop hardness, linear elastic, nonlinear elastic
Doplňující informace
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1?This standard serves as a guide to existing standards or variations of existing standards that may be applicable to determine specific mechanical properties of materials made with an additive manufacturing process. 1.2?As noted in many of these referenced standards, there are several factors that may influence the reported properties, including material, material anisotropy, method of material preparation, porosity, method of specimen preparation, testing environment, specimen alignment and gripping, testing speed, and testing temperature. These factors should be recorded, to the extent that they are known, according to Practice F2971 and the guidelines of the referenced standards. 1.3?The following standards are not referred to directly in the guide but also have information that may be useful in the testing of metal test specimens made via additive manufacturing: A370, A1058, B211, B348, B557, B565, B724, B769, E3, E6, E7, E290, E467, E468, E837, E915, E1049,E1823, E1942. 1.4?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Doporučujeme:
Aktualizace technických norem
Chcete mít jistotu, že používáte pouze platné technické normy?
Nabízíme Vám řešení, které Vám zajistí měsíční přehled o aktuálnosti norem, které používáte.
Chcete vědět více informací? Podívejte se na tuto stránku.
