Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM F3111-16

Standard Specification for Heavy Hex Structural Bolt/Nut/Washer Assemblies, Alloy Steel, Heat Treated, 200 ksi Minimum Tensile Strength

Přeložit název

NORMA vydána dne 1.4.2016

Jazyk
Provedení	PDF - okamžité stažení - 1 617.90 Kč PDF + redline - ihned - 1 941.50 Kč Tištěné - 1 617.90 Kč Tisk + redline - 1 941.50 Kč
Dostupnost	SKLADEM
Cena	1 617.90 Kč bez DPH
1 617.90 Kč

Informace o normě:

Označení normy: ASTM F3111-16
Datum vydání normy: 1.4.2016
Kód zboží: NS-638539
Počet stran: 15
Přibližná hmotnost: 45 g (0.10 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Kategorie - podobné normy:

Mechanické spojovací součásti obecně

Anotace textu normy ASTM F3111-16 :

Keywords:
alloy steel, fasteners, heavy hex structural bolt, heavy hex structural bolt/nut/washer assembly, structural,, ICS Number Code 21.060.01 (Fasteners in general)

Doplňující informace

Significance and Use

A2.4 Significance and Use

A2.4.1 This test method describes the testing procedure that shall be used to qualify material for use in ASTM F3111 bolts made of any steel composition permitted by this specification. The test method measures the susceptibility of the material to the influence of an externally applied potential (see A2.7.2.3.2) by testing for the threshold of embrittlement in a salt solution environment.

1. Scope

1.1 This specification covers heat treated, alloy steel, heavy hex structural bolt/nut/washer assemblies, also referred to as “sets,” having a tensile strength of 200 to 215 ksi. These assemblies are capable of developing a minimum predetermined tension when installed by applying an initial torque followed by rotation to the nut or bolt head, while at the same time preventing the rotation of the opposite side of the assembly.

Note 1: The installations in Appendix X1 are important to the proper application of this product.

1.2 An assembly consists of a heavy hex structural head bolt, nut and two washers covered by this specification.

1.3 The assemblies are available in sizes 1 in. to 1 ¹/₄ in. inclusive.

1.4 The fastener assemblies are intended for use in structural connections in the following environmental conditions:

1.4.1 Interiors, normally dry, including interiors where structural steel is embedded in concrete, encased in masonry or protected by membrane or noncorrosive contact type fireproofing.

1.4.2 Interiors and exteriors, normally dry, under roof, where the installed assemblies are soundly protected by a shop-applied or field-applied coating to the structural steel system.

1.5 The fastener assemblies are not intended for use in structural connections in the following environments, with or without protection by a shop-applied or field-applied coating to the structural steel system:

1.5.1 Exteriors not under roof.

1.5.2 Chemical environments in which strong concentrations of highly corrosive gases, fumes, or chemicals, either in solution or as concentrated liquids or solids, contact the fasteners or their protective coating.

1.5.3 Heavy industrial environments severe enough to be classified as a chemical environment as described in 1.5.2.

1.5.4 Condensation and high humidity environments maintaining almost continuous condensation, including submerged in water and soil.

1.5.5 Cathodically protected environments, in which current is applied to the structural steel system by the sacrificial anode method or the DC power method.

1.6 Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.7 The following precautionary statement pertains only to the test method portions, Section 13, Section 14 and Annex A2 of this Specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

F2660-20	Standard Test Method for Qualifying Coatings for Use on F3125 Grade A490 Structural Bolts Relative to Environmental Hydrogen Embrittlement
G3-14(2019)	Standard Practice for Conventions Applicable to Electrochemical Measurements in Corrosion Testing
G15-08	Standard Terminology Relating to Corrosion and Corrosion Testing (Withdrawn 2010)
G44-21	Standard Practice for Exposure of Metals and Alloys by Alternate Immersion in Neutral 3.5 % Sodium Chloride Solution
F2078-22	Standard Terminology Relating to Hydrogen Embrittlement Testing
F1789-23	Standard Terminology for F16 Mechanical Fasteners
E4-21	Standard Practices for Force Calibration and Verification of Testing Machines
F606-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
F519-23	Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating/Coating Processes and Service Environments
F2328-17(2022)	Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts
F1624-12(2018)	Standard Test Method for Measurement of Hydrogen Embrittlement Threshold in Steel by the Incremental Step Loading Technique
E709-21	Standard Guide for Magnetic Particle Testing
A751-21	Standard Test Methods and Practices for Chemical Analysis of Steel Products
E1444/E1444M-22a	Standard Practice for Magnetic Particle Testing for Aerospace (Includes all amendments and changes 7/11/2022).
F606/F606M-21	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
F788-20	Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series
F812-12	Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series
F1470-24	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
F1789-23	Standard Terminology for F16 Mechanical Fasteners

Odebírejte informace o nově vydaných normách ZDARMA:

Chcete pravidelně odebírat informace o nově vycházejících normách z celého světa a to zcela zdarma?
Přihlašte se k odběru. Vše je velice jednoduché a absolutně ZDARMA.
Na výběr máte vydavatele z celého světa.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.