Cookies
Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů. Souhlas udělíte kliknutím na tlačítko „OK“.
ASTM F3057-16
Standard Test Method for Electromagnetic Shielding Effectiveness of Glazings
Automaticky přeložený název:
Standardní testovací metoda pro elektromagnetické stínění účinnosti zasklení
NORMA vydána dne 1.2.2016
Informace o normě:
Označení normy: ASTM F3057-16
Poznámka: NEPLATNÁ
Datum vydání normy: 1.2.2016
Kód zboží: NS-633429
Počet stran: 8
Přibližná hmotnost: 24 g (0.05 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM
Kategorie - podobné normy:
Anotace textu normy ASTM F3057-16 :
Keywords:
coated glass, electromagnetic measurements, filmed glazing, glass, glazing, laminated glass, laminates, magnetic fields, plane waves, radio frequencies, shielding effectiveness,, ICS Number Code 81.040.20 (Glass in building)
Doplňující informace
| Significance and Use | ||||||||||||
|
5.1 This test method provides measurement procedures for determining the electromagnetic shielding effectiveness of glazings and glazing configurations as a material. This test method specifies a method for comparing the glazings and glazing configurations as an infill component to allow comparison of between different infills. In addition, this test method is written to minimize variations in measured shielding effectiveness at a given frequency and test point regardless of test personnel, equipment, and test site. Therefore, the shielding effectiveness of a glazing or glazing configuration from any supplier can be determined. This test method specifies a minimum set of measurements over a frequency range to determine shielding effectiveness. 5.2 Source Fields—Performance of a shielded enclosure and glazing or glazing configurations are to be assessed for three source fields: magnetic, electric, and plane wave. |
||||||||||||
| 1. Scope | ||||||||||||
|
1.1 This test method covers the determination of the electromagnetic shielding effectiveness of glazings or glazing configurations. 1.1.1 The intended application of this test method is for glazings or glazing configurations to be evaluated for their transmittance or shielding capability to electromagnetic frequencies. 1.1.2 This is a component test. It is not applicable to full systems such as walls, floors, ceilings, shielded racks, or window systems. 1.1.3 The intention of this test method is to standardize a measurement procedure for glazings or glazing configurations, with and without coatings, films, interlayers, or other enhancements, as single or insulating units at a standard size and when mounted in a standardized frame. 1.1.4 This test method is to provide a means of generating data for the glazing or glazing configuration infills that can be used by the consumer, designer, and system manufacturer to understand the capability and contribution of glazings or glazing configurations to a system used for Electromagnetic Interference (EMI) security. 1.2 This test method is for use in the assessment of EMI transmittance for frequency ranges 100 kHz to 20 GHz. Specific test frequencies within these ranges are required. 1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 8 on Hazards. |
||||||||||||
| 2. Referenced Documents | ||||||||||||
|
Doporučujeme:
Aktualizace zákonů
Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.
