Pozor!

Ve Vašem prohlížeči není aktuálně povoleno spouštění Javascriptu. Je možné, že některé funkce nebudou fungovat správně. Pro plnou funkčnost internetového obchodu doporučujeme povolit Javascript. Zde jsou instrukce jak povolit JavaScript ve Vašem webovém prohlížeči.

Zobrazovaná měna: Kč

Zobrazení ceny: bez DPH

Doplňující informace

ASTM F3043-14

Standard Specification for “Twist Off” Type Tension Control Structural Bolt/Nut/Washer Assemblies, Alloy Steel, Heat Treated, 200 ksi Minimum Tensile Strength

Automaticky přeložený název:

Standardní specifikace pro & ldquo ; Twist Off & rdquo ; Druh napínání: Kontrolní Strukturální šroub / matice / Podložka Assemblies , legované oceli , tepelně zpracované , 200 ksi Minimální pevnost v tahu

NORMA vydána dne 1.10.2014

Jazyk
Provedení	PDF - okamžité stažení - 2 087.10 Kč Tištěné - 2 087.10 Kč
Dostupnost	SKLADEM
Cena	2087.10 Kč bez DPH
2 087.10 Kč

Informace o normě:

Označení normy: ASTM F3043-14
Poznámka: NEPLATNÁ
Datum vydání normy: 1.10.2014
Kód zboží: NS-54891
Počet stran: 14
Přibližná hmotnost: 42 g (0.09 liber)
Země: Americká technická norma
Kategorie: Technické normy ASTM

Tisk

Odeslat známému

Dotaz

Anotace textu normy ASTM F3043-14 :

Keywords:

alloy steel, alternate design fasteners, bolts, fasteners, spline end, structural, tension control bolt, tension control bolt assembly, twist-off bolt,

Doplňující informace

Significance and Use

A2.4 Significance and Use

A2.4.1 This test method describes the testing procedure that shall be used to qualify material for use in ASTM F3043 bolts made of any steel composition permitted by this specification. The test method measures the susceptibility of the material to the influence of an externally applied potential (see A2.7.2.3.2) by testing for the threshold of embrittlement in a salt solution environment.

1. Scope

1.1 This specification covers one style of heat treated, alloy steel, tension control bolt-nut-washer assemblies, also referred to as “sets,” having a tensile strength of 200 to 215 ksi. These assemblies are capable of developing a minimum predetermined tension when installed by applying torque to the nut, while at the same time applying a counter torque to separate the spline end from the body of the bolt using an appropriate spline drive installation tool.

1.2 An assembly consists of a tension control bolt with spline end, nut and washer covered by this specification.

1.3 The assemblies are available with round heads described in Section 10, in sizes 1 in. to 1¹/₄ in. inclusive.

1.4 The fastener assemblies are intended for use in structural connections in the following environmental conditions:

1.4.1 Interiors, normally dry, including interiors where structural steel is embedded in concrete, encased in masonry or protected by membrane or noncorrosive contact type fireproofing.

1.4.2 Interiors and exteriors, normally dry, under roof, where the installed assemblies are soundly protected by a shop-applied or field-applied coating to the structural steel system.

1.5 The fastener assemblies are not intended for use in structural connections in the following environments, with or without protection by a shop-applied or field-applied coating to the structural steel system:

1.5.1 Exteriors not under roof.

1.5.2 Chemical environments in which strong concentrations of highly corrosive gases, fumes, or chemicals, either in solution or as concentrated liquids or solids, contact the fasteners or their protective coating.

1.5.3 Heavy industrial environments severe enough to be classified as a chemical environment as described in 1.5.2.

1.5.4 Condensation and high humidity environments maintaining almost continuous condensation, including submerged in water and soil.

1.5.5 Cathodically protected environments, in which current is applied to the structural steel system by the sacrificial anode method or the DC power method.

1.6 Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.7 The following precautionary statement pertains only to the test method portions, Section 15, Section 16 and Annex A2 of this Specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

E8/E8M-24	Standard Test Methods for Tension Testing of Metallic Materials
F519-23	Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating/Coating Processes and Service Environments
F606-14	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
F1624-12(2018)	Standard Test Method for Measurement of Hydrogen Embrittlement Threshold in Steel by the Incremental Step Loading Technique
F1789-23	Standard Terminology for F16 Mechanical Fasteners
F2078-22	Standard Terminology Relating to Hydrogen Embrittlement Testing
F2660-20	Standard Test Method for Qualifying Coatings for Use on F3125 Grade A490 Structural Bolts Relative to Environmental Hydrogen Embrittlement
G3-14(2019)	Standard Practice for Conventions Applicable to Electrochemical Measurements in Corrosion Testing
G15-08	Standard Terminology Relating to Corrosion and Corrosion Testing (Withdrawn 2010)
G44-21	Standard Practice for Exposure of Metals and Alloys by Alternate Immersion in Neutral 3.5 % Sodium Chloride Solution
G82-98(2021)e1	Standard Guide for Development and Use of a Galvanic Series for Predicting Galvanic Corrosion Performance (Includes all amendments and changes 1/21/2021).
E4-21	Standard Practices for Force Calibration and Verification of Testing Machines
A751-21	Standard Test Methods and Practices for Chemical Analysis of Steel Products
E709-21	Standard Guide for Magnetic Particle Testing
E1444/E1444M-22a	Standard Practice for Magnetic Particle Testing for Aerospace (Includes all amendments and changes 7/11/2022).
F606/F606M-21	Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
F788-20	Standard Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series
F812-12	Standard Specification for Surface Discontinuities of Nuts, Inch and Metric Series
F1470-24	Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
F1789-23	Standard Terminology for F16 Mechanical Fasteners
F2328-17(2022)	Standard Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts

Doporučujeme:

Aktualizace zákonů

Chcete mít jistotu o platnosti užívaných předpisů?
Nabízíme Vám řešení, abyste mohli používat stále platné (aktuální) legislativní předpisy.
Chcete vědět více informací? Podívejte se na tuto stránku.

Zde máte možnost přizpůsobit si nastavení souborů cookies v souladu s vlastními preferencemi.

Potřebujeme váš souhlas k využití jednotlivých dat, aby se vám mimo jiné mohly ukazovat informace týkající se vašich zájmů.